GREAT PLAINS 3S-3000-3210 Operator'S Manual Download

Page: 65 / 118

3S-3000/F/HD/HDF

Table of Contents

Index

Adjustments

2018-06-18

Table of Contents

Index

195-441M

Marker Disk Adjustment

Sharp Object Hazard:

Marker disks may be sharp. Use caution when making
adjustments in this area.

Mark Width

Refer to Figure 64

is the direction of travel.

To change angle of cut, and the width of the mark, loosen



-inch bolts

holding the disk assembly.

For a wider mark

, increase the angle of the marker

with respect to the tube

. For a narrower mark

reduce the angle.

Tighten bolts

Direction of Cut

To have the marker throw dirt out, invert the disk on the
spindle, and invert the disk assembly.

Figure 64

Marker Disk Angle

11757

Figure 65

Marker Disk Inverted

11248

Summary of Contents for 3S-3000-3210























































































































Search results

Summary of Contents for 3S-3000-3210

Reviews:

Related manuals for 3S-3000-3210

Brands by name

Popular brands

GREAT PLAINS 3S-3000-3210, Operator'S Manual

Search results

Summary of Contents for 3S-3000-3210

Reviews:

Related manuals for 3S-3000-3210

Brands by name

Popular brands