GREAT PLAINS 3S-3000-3210 Operator'S Manual Download

Page: 23 / 118

3S-3000/F/HD/HDF

Table of Contents

Index

Preparation and Setup

2018-06-18

Table of Contents

Index

195-441M

Electrical Connections

Refer to Figure 7

Plug drill electrical lead into tractor seven-pin connector.
If your tractor is not equipped with a seven-pin connector,
contact your dealer for installation.

Refer to Figure 8

If the drill is equipped with the optional shaft monitor,
mate the connector for the cab display.

See “

Shaft Monitor

” on page 92 for ordering

information.

Refer to Figure 9

If the drill is equipped with the point row option, mate the
connector for the cab control.

See “

Point Row Clutch

” on page 91 for ordering

information.

Figure 7

Lighting Connector

26467

Figure 8

Shaft Monitor Connector

34222

Figure 9

Point-Row Connector

26469

Summary of Contents for 3S-3000-3210























































































































Search results

Summary of Contents for 3S-3000-3210

Reviews:

Related manuals for 3S-3000-3210

Brands by name

Popular brands

GREAT PLAINS 3S-3000-3210, Operator'S Manual

Search results

Summary of Contents for 3S-3000-3210

Reviews:

Related manuals for 3S-3000-3210

Brands by name

Popular brands