GREAT PLAINS 3S-3000-3210 Operator'S Manual Download Page 89

Page: 89 / 118

3S-3000/F/HD/HDF

Table of Contents

Index

Maintenance and Lubrication

2018-06-18

Table of Contents

Index

195-441M

Transport Lift Pivots

2 grease fittings inside pivot

Type of Lubrication: Grease
Quantity: Until grease emerges at pivot ends

Transport Axle

2 grease fittings

Type of Lubrication: Grease
Quantity: Until grease emerges

Mainframe Pivots

2 grease fittings each pivot; 4 total

Type of Lubrication: Grease
Quantity: Until grease emerges

These grease fittings are more accessible with the drill
folded.

Seed Cup Drive Shaft Sprocket

2 sliding sprockets; one each side
Type of Lubrication: Oil
Quantity: Coat thoroughly

Move the Seed Rate adjustment handle back and forth to
get oil into the square bore. Perform this with seed box
empty, or handle may be difficult to set to 100.

15543

15541

15540

12126

Summary of Contents for 3S-3000-3210























































































































Search results

Summary of Contents for 3S-3000-3210

Reviews:

Related manuals for 3S-3000-3210

Brands by name

Popular brands

GREAT PLAINS 3S-3000-3210, Operator'S Manual

Search results

Summary of Contents for 3S-3000-3210

Reviews:

Related manuals for 3S-3000-3210

Brands by name

Popular brands