GREAT PLAINS 3S-3000-3210 Operator'S Manual Download | Manualshive

Page: 58 / 118

background image

2018-06-18

Table of Contents

195-441M

3S-3000/F/HD/HDF

Table of Contents

Adjustments

54

00HD Row Unit Adjustments

Refer to Figure 52
(which depicts a row unit fully populated with all optional
accessories supported for use with the 3S-3000HD drill)

From front to back, a Great Plains 00HD Series row unit
can include the following capabilities (some optional):

1.

Opener height adjustment: standard
If a few rows need to run deeper, such as in tire
tracks, the arm’s pivot point may be lowered. See
“

Opener Height

” on page 55.

2.

Single Down Pressure Spring: standard
Each row unit is mounted on the drill as a pivoting
arm which allows the row unit to independently move
up and down. The adjustable spring provides the
force to get the row unit and attachments into the
soil. See “

Row Unit Down Pressure (Spring)

3.

Disc Blades: standard, 2 per row unit
Double disc blades open a furrow, creating the seed
bed. Spacers adjust the blades for a clean furrow.
See “

Disk Blade Adjustments

” on page 56.

4.

Seed delivery tube: standard
No adjustments are necessary.

5.

Disk Scraper: optional
In sticky soils, a scraper helps keep the opener disks
operating freely. See “

Disk Scraper Adjustments

6.

Seed firmer: seed flap (not shown) standard:

Keeton seed firmer (shown)
Improves seed-soil contact, and provides a stable
arm for a low-rate liquid fertilizer delivery tube. See
“

Keeton Seed Firmer Adjustment

” on page 57.

Seed-Lok™ firming wheel (not shown)
Improves seed-soil contact. See “

Seed-Lok™ Seed

Firmer Lock-Up

” on page 57.

7.

Press wheels: standard (choice of types)
These close the seed trench. The wheels also
support the free end of the row unit, and provide the
primary control over seeding depth. See “

Depth (Press Wheel Height)

” on page 58.

Certain Machine Damage:

Do not back up with row units in the ground. To do so will
cause severe damage and row unit plugging.

Figure 52

00HD Series Row Unit

26427

«
...
56
57
58
59
60
...
»

Summary of Contents for 3S-3000-3210























































































































Reviews:

No comments

Related manuals for 3S-3000-3210

Brand: Landoll Pages: 102

Brand: Lincoln Electric Pages: 13

Brand: GALA Pages: 32

SuperSeeder 2400

Brand: Stinger Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands