GREAT PLAINS 3S-3000-3210 Operator'S Manual Download Page 3 | Manualshive

Page: 3 / 118

background image

3S-3000/F/HD/HDF

Table of Contents

iii

2018-06-18

195-441M

©

Copyright 2001, 2002, 2003, 2006, 2007, 2009, 2010, 2012, 2014, 2017 All rights Reserved

Great Plains Manufacturing, Inc. provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been
taken in the preparation of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumed for
damages resulting from the use of the information contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and improve its products as
it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future.

Trademarks of Great Plains Manufacturing, Inc. include: AccuShot, Max-Chisel, Row-Pro,

Singulator Plus, Short Disk, Swath Command, Terra-Tine, Ultra-Chisel, and X-Press.

Registered Trademarks of Great Plains Manufacturing, Inc. include: Air-Pro, Clear-Shot, Discovator, Great Plains, Land Pride, MeterCone,

Nutri-Pro, Seed-Lok, Solid Stand, Terra-Guard, Turbo-Chisel, Turbo-Chopper, Turbo-Max, Turbo-Till, Ultra-Till, Whirlfilter, and Yield-Pro.

Brand and Product Names that appear and are owned by others are trademarks of their respective owners.

Printed in the United States of America

Table of Contents

Important Safety Information.................................................1

Safety Decals ....................................................................6

Introduction...........................................................................14

Document Family.............................................................14
Description of Unit ...........................................................14

Intended Usage ........................................................14
Models Covered .......................................................14

Using This Manual...........................................................15

Definitions.................................................................15

Owner Assistance............................................................16

Preparation and Setup .........................................................17

Pre-Setup Checklist.........................................................17
Hitching............................................................................17
Electrical Connections .....................................................19
Hydraulic Hose Hookup...................................................20
Check Drill Level..............................................................20
Setting the Bypass Valve.................................................21

Operating Instructions .........................................................23

General Description.........................................................23
Pre-Start Checklist...........................................................24
Raising and Lowering Openers .......................................24

Opener Lock Up .......................................................24

Folding.............................................................................25
Raising Drill (Transport Lift).............................................26

Transport Lift ............................................................27

Transport .........................................................................28

Weights for Tractor Requirements ...........................28
Marker Transportation ..............................................28
Transport Checklist ..................................................29

Lowering Drill (Transport Lift) ..........................................30

Transport Lower .......................................................30

Unfolding .........................................................................31

Folding and Unfolding Quick Reference...................31

Opener Operation............................................................32

Active Hydraulic Systems.........................................33
Priority Flow Hydraulic Systems...............................34
Non-Active Hydraulic System...................................34
Position Seed Cup Doors .........................................35

Loading Materials ............................................................36

Loading Main Seed Box ...........................................36
Loading Small Seeds Box ........................................36
Loading Fertilizer Compartment ...............................37

Fertilizer Box Operation...................................................38

Applying Seed and Fertilizer ....................................38
Using Fertilizer Compartment...................................39

Seeding with Both Compartments............................39
Initial Seeding Depth ................................................40

Acremeter Operation .......................................................40
Marker Operation ............................................................41

Single Marker Operations ........................................41
Dual Marker Operations ...........................................41

Lift Selector Valve Operation...........................................42
Point Row Operation .......................................................42
Shaft Monitor Operation ..................................................43
Field Operations ..............................................................43

Final Field Checklist .................................................43
Planting Sequence ...................................................43

Parking ............................................................................44

Parking with Drill Unfolded .......................................44
Parking with Drill Folded ..........................................44

Storage............................................................................45

Adjustments..........................................................................46

Setting Material Rates .....................................................47

Setting Main Box Seed Rate ....................................47
Setting Fertilizer Rate...............................................47
Small Seeds Rate ....................................................47

Frame Level ....................................................................48
Frame Weight..................................................................49
Opener Frame Down-Force ............................................50

Setting Hydraulic Down-Pressure ............................51

Opener-Subframe Adjustment.........................................52
00 Row Unit Adjustments ................................................53
00HD Row Unit Adjustments...........................................54

Opener Height..........................................................55
Row Unit Down Pressure (Spring) ...........................55
Disk Blade Adjustments ...........................................56
Disk Scraper Adjustments........................................56
Seed Firmer Adjustments.........................................57
Opener Depth (Press Wheel Height) .......................58

Marker Adjustments ........................................................59

Marker Width............................................................59
Marker Chain Adjustment.........................................60
Marker Disk Adjustment ...........................................61
Marker Speed...........................................................62

Troubleshooting ...................................................................63
Maintenance and Lubrication..............................................65

Materials Clean-Out ........................................................66

Main Seed Box Clean-Out .......................................66
Fertilizer Box Clean-Out...........................................66
Small Seeds Box Clean-Out ....................................67

«
1
2
3
4
5
...
»

Summary of Contents for 3S-3000-3210























































































































Reviews:

No comments

Related manuals for 3S-3000-3210

Origo Feed Spool Gun

Brand: ESAB Pages: 44

Brand: BLEC Pages: 38

Matrix Omni-Flow

Brand: Vivid Pages: 35

Brand: Facom Pages: 48

Maxi Drill 6000

Brand: SKY Agriculture Pages: 103

Brand: Chapin Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands