manualshive.com logo in svg

GREAT PLAINS 3S-3000-3210, Operator'S Manual

The GREAT PLAINS 3S-3000-3210 Operator's Manual is now available for free download on our website. This comprehensive manual provides all the necessary information to efficiently operate and maintain the product. Visit manualshive.com to access the manual and unlock the full potential of your GREAT PLAINS 3S-3000-3210 machinery.

Share
Download
background image

2018-06-18

Table of Contents

Index

195-441M

3S-3000/F/HD/HDF

Table of Contents

Index

Introduction

14

Introduction

Great Plains welcomes you to its growing family of new
product owners. Your 30-Foot Three-Section Folding Drill
has been designed with care and built by skilled workers
using quality materials. Proper setup, maintenance, and
safe operating practices will help you get years of
satisfactory use from the machine.

Description of Unit

The 3S-3000/F/HD/HDF is a towed seeding implement.
This two-section drill has a working width of 26 feet and
folds to a transport width of 15 feet. The drill has
straight-arm, double-disk openers. The 3S-3000HD
models feature double disk heavy duty openers. The
opener disks make a seed bed, and seed tubes mounted
between the disks place seed in the furrow. Press wheels
following the opener disks close the furrow and gauge
opener seeding depth. 

Intended Usage

Use this implement to seed production-agriculture crops
in conventional or minimum tillage applications. Do not
modify the drill for use with attachments other than Great
Plains options and accessories specified for use with the
3S-3000 Drill.

Document Family

195-441M

Owner’s Manual (this document)

195-200P

3S-3000/F Parts Manual

195-069P

3S-3000HD Parts Manual

195-325B

3S-3000/F/HD/HDF Seed Rate Manual

Models Covered

Using This Manual

This manual familiarizes you with safety, assembly,
operation, adjustments, troubleshooting, and
maintenance. Read this manual and follow the
recommendations to help ensure safe and efficient
operation. 

The information in this manual is current at printing.
Some parts may change to assure top performance.

Definitions

The following terms are used throughout this manual.

Right-hand and left-hand as used in this manual are
determined by facing the direction the machine will travel
while in use unless otherwise stated.

Paragraphs in this format present a crucial point of information
related to the current topic.

Read and follow the directions to remain safe, avoid serious
damage to equipment and ensure desired field results.

NOTE:

Paragraphs in this format provide useful information
related to the current topic.

Null4-AAC:

Figure 1

3S-3000 drill

17254

3S-3000-3210

32-row, 10 inch (25.4 cm)

3S-3000-4275

42-row, 7.5 inch (19 cm)

3S-3000-5206

52-row, 6 inch (15 cm)

3S-3000F-3210

32-row, 10 inch (25.4 cm)

3S-3000F-4275

42-row, 7.5 inch (19 cm)

3S-3000F-5206

52-row, 6 inch (15 cm)

3S-3000HD/F-3210

32-row, 10 inch (25.4 cm)

3S-3000HD/F-4275

42-row, 7.5 inch (19 cm)

3S-3000HD/F-5206

52-row, 6 inch (15 cm)

Dealer QRC

The QR Code (Quick Reference) to the
left will take you to available dealers for
Great Plains products. Refer to the
Parts Manual QR Locater for detailed
instructions.

Manual Family QRC

The QR Code (Quick Response) to the
left will take you to this machine’s family
of manuals. Use your smart phone or
tablet to scan the QR Code with an
appropriate App to begin viewing.

Summary of Contents for 3S-3000-3210























































































































Reviews:

No comments

Related manuals for 3S-3000-3210

Panasonic YW-50DNW Operating Instructions Manual preview
YW-50DNW
Brand: Panasonic Pages: 20
Frama AF Service Manual preview
AF
Brand: Frama Pages: 41

Brands by name

Popular brands

Load more brands