GREAT PLAINS 3S-3000-3210 Operator'S Manual Download Page 41

Page: 41 / 118

3S-3000/F/HD/HDF

Table of Contents

Index

Operating Instructions

2018-06-18

Table of Contents

Index

195-441M

Loading Fertilizer Compartment

Load fertilizer after transport if possible. Some spillage
can occur through meters during transport, even with the
drive system disengaged.

Possible Agricultural Chemicals Hazards:

Take all necessary materials safety
precautions when loading dusty seed,
treated seed or fertilizer.

Refer to Figure 29

Clean any seed or debris from fertilizer
compartment. Close and latch the clean-out door.
Make sure all door latches

are engaged before

loading fertilizer compartment.

Check that any offset box dividers are set to the
desired compartment ratio. See “

Offset Box

Divider

” on page 91.

Refer to Figure 30

Close the seed/fertilizer flap so seed and fertilizer
cannot pass between compartments.

Flap flips forward to block passage. The flap top
edge is secured to the dividers. Rotate the bent
clips to engage the edge of the flap, and tighten the
knobs

Refer to Figure 31

Open spill flap

over fertilizer compartment and

swivel back until it rests against open drill-box lid.
The spill flap serves as a spill guard to keep fertilizer
out of the seed compartment.

Fill fertilizer compartment. Make sure material is
loaded or spread evenly across all partitions. Use
tool or gloved hand. Do not overfill boxes.

To reduce wear, remove main drive shaft chains for
main seed boxes.

Figure 29

Latch for Fertilizer Clean-out Door

16383

Figure 30

Seed/Fertilizer Flap Closed

16383

Figure 31

Spill Flap

16375

Summary of Contents for 3S-3000-3210























































































































Search results

Summary of Contents for 3S-3000-3210

Reviews:

Related manuals for 3S-3000-3210

Brands by name

Popular brands

GREAT PLAINS 3S-3000-3210, Operator'S Manual

Search results

Summary of Contents for 3S-3000-3210

Reviews:

Related manuals for 3S-3000-3210

Brands by name

Popular brands