GREAT PLAINS 3S-3000-3210 Operator'S Manual Download Page 10

Page: 10 / 118

2018-06-18

Table of Contents

Index

195-441M

3S-3000/F/HD/HDF

Table of Contents

Index

Important Safety Information

Safety Decals

Safety Reflectors and Decals

Your drill comes equipped with all lights, safety reflectors
and decals in place. They were designed to help you
safely operate your drill.



Read and follow decal directions.



Keep lights in operating condition.



Keep all safety decals clean and legible.



Replace all damaged or missing decals. Order new decals
from your Great Plains dealer. Refer to this section for
proper decal placement.



When ordering new parts or components, also request
corresponding safety decals.

Slow Moving Vehicle Reflector (S/N S3495-)

818-003C

Center of rear center section;
1 total

Slow Moving Vehicle Reflector (S/N S3496+)

818-055C

Center of rear center walkboard;
1 total

To install new decals:

Clean the area on which the decal is to be placed.

Peel backing from decal. Press firmly on surface,
being careful not to cause air bubbles under decal.

15568

68447A

Summary of Contents for 3S-3000-3210























































































































Search results

Summary of Contents for 3S-3000-3210

Reviews:

Related manuals for 3S-3000-3210

Brands by name

Popular brands

GREAT PLAINS 3S-3000-3210, Operator'S Manual

Search results

Summary of Contents for 3S-3000-3210

Reviews:

Related manuals for 3S-3000-3210

Brands by name

Popular brands