GREAT PLAINS 3S-3000-3210 Operator'S Manual Download | Manualshive

Page: 28 / 118

background image

2018-06-18

Table of Contents

195-441M

3S-3000/F/HD/HDF

Table of Contents

Operating Instructions

24

Pre-Start Checklist



Lubricate the drill as indicated under Lubrication,
“

Maintenance and Lubrication

” on page 65.



Check the tires for proper inflation according to
“

Hydraulic Diagrams

” on page 99.



Check for worn or damaged parts and repair or
replace before going to the field.



Check all nuts, bolts and screws. Tighten bolts as
specified on “

Torque Values Chart

Raising and Lowering Openers

Opener sub-frames are on a dedicated hydraulic circuit.
Openers raise and lower independently of the drill frame
(which is raised and lowered by the transport lift circuit).

When lowered, the opener circuit can use live hydraulic
power to regulate down-pressure. To operate with live
hydraulic power, connect the opener lift circuit to the #1
remote hydraulic circuit or the circuit designed for
HYDRAULIC MOTOR control. On many CLOSED
CENTER or PRESSURE/FLOW COMPENSATED
tractors the #1 circuit is the circuit designed to supply live
hydraulic power to remote locations.

On the standard drill, the openers raise and lower as a
group, from a tractor cab lever. If the Point Row Option is
installed, each section can raise and lower
independently, using switches on the point row control
module in the tractor cab.

If the Two Outlet conversion kit is installed, a selector
valve near the hitch must be operated to switch between
Opener Lift and Transport Lift. During field operations,
this valve is in the Opener Lift position.

Opener Lock Up

The openers must be locked up for transporting or for
working under the drill.

Refer to Figure 13

Each opener lift assembly has wire rod lock handle

,

and a cylinder lock status indicator

on the lock hook.



NOTE:

Opener transport lock handles

can be moved with

openers up or down, but transport locks only engage
after openers are raised completely and disengage
after openers are lowered completely. There are two
lock handles on each drill section, six handles total.

Lock Up Openers

1.

Position opener transport handles in ROAD position.

2.

Raise openers completely.

Crushing Hazard:

Raising openers on unfolded, unhitched drill will cause drill
tongue to rise suddenly, which could cause serious injury or
death. Be certain that drill is hitched securely to your tractor
drawbar and the safety chain is securely attached to tractor
before raising openers and unfolding drill.

Figure 13

Opener Lock-Up

15549

1

2

«
...
26
27
28
29
30
...
»

Summary of Contents for 3S-3000-3210























































































































Reviews:

No comments

Related manuals for 3S-3000-3210

Brand: Little Wonder Pages: 18

Brand: GALA Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands