GREAT PLAINS 3S-3000-3210 Operator'S Manual Download | Manualshive

Page: 69 / 118

background image

2018-06-18

Table of Contents

195-441M

3S-3000/F/HD/HDF

Table of Contents

Maintenance and Lubrication

65

Maintenance and Lubrication

Proper servicing and maintenance is the key to long
implement life. With careful and systematic inspection,
you can avoid costly maintenance, downtime and repair.

Always turn off and remove the tractor key before making
any adjustments or performing any maintenance.

Crushing Hazard:

You may be severely injured or killed by being crushed under a
falling implement. Always have frame sufficiently blocked up
when working on, and particularly under implement.

High Pressure Fluid Hazard:

Escaping fluid under pressure can have sufficient pressure to
penetrate the skin. Check all hydraulic lines and fittings before
applying pressure. Fluid escaping from a very small hole can
be almost invisible. Use paper or cardboard, not body parts,
and wear heavy gloves to check for suspected leaks. If injured,
seek immediate medical assistance from a doctor that is
familiar with this type of injury.

After using drill for several hours, check all bolts to be
sure they are tight.

1.

Securely block drill before working on it.

2.

Lubricate areas listed under “

Lubrication

3.

Clean any fittings that do not take grease.

4.

Inflate tires as specified on “

Tire Inflation Chart

5.

Inspect hydraulic hoses for cuts, cracks and aging.
Check fittings for evidence of leaks.

6.

Keep disk scrapers properly adjusted.

7.

Replace any worn, damaged or illegible safety
decals. Order new decals from your Great Plains
dealer. See “

Safety Decals

OFF

«
...
67
68
69
70
71
...
»

Summary of Contents for 3S-3000-3210























































































































Reviews:

No comments

Related manuals for 3S-3000-3210

Brand: LOBSTER Pages: 30

Brand: Dynapac Pages: 626

23508—400000000

Brand: Toro Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands