manualshive.com logo in svg

GREAT PLAINS 3S-3000-3210, Operator'S Manual

The GREAT PLAINS 3S-3000-3210 Operator's Manual is now available for free download on our website. This comprehensive manual provides all the necessary information to efficiently operate and maintain the product. Visit manualshive.com to access the manual and unlock the full potential of your GREAT PLAINS 3S-3000-3210 machinery.

Share
Download
background image

2018-06-18

Table of Contents

Index

195-441M

3S-3000/F/HD/HDF

Table of Contents

Index

Operating Instructions

30

Lowering Drill (Transport Lift)

Lowering from Transport Lift must be completed prior to
unfolding.

Transport Lift is on a dedicated hydraulic circuit. The
center main frame raises and lowers independently of
the opener sub-frames (which are raised and lowered by
the Opener Lift circuit).

The Transport Lift circuit also includes a cylinder for the
Transport Hooks, which lifts and restrains the
outer/forward ends of the wing sections when folded.

Transport Lift is normally used only when the drill is
folded. Opener Lift, and not Transport Lift, is used for
headland turns in field operations.

Transport Lower

1.

Park tractor and drill on level ground with tractor
transmission in Park. Be aware of clearance needed
to unfold drill.

2.

If the Two Outlet conversion kit is installed, confirm
that the selector valve, located near the hitch, is set
for Transport Lift operations. See “

Lift Selector

Valve Operation

” on page 42.

3.

Slowly extended the Transport Lift circuit lever until
all three Transport Lift circuit cylinders are fully
extended (2 at transport wheels; 1 at transport hooks
on tongue). Set circuit lever to off or neutral (not
float).

Refer to Figure 20

4.

Rotate cylinder lock channels down and forward off
transport lift cylinders.

Refer to Figure 21

5.

Rotate cylinder lock channel up and forward off front
box lift cylinder.

6.

Slowly reverse the lift circuit lever and begin lowering
the drill. Keep the circuit engaged until all three
cylinders are completely retracted. Set circuit to off
or neutral.

The drill is now ready for unfolding.

Figure 20

Transport Lift Cylinder Lock

18960

Figure 21

Front Box Lift Cylinder

Locked for Transport

15631

Figure 22

Front Box Lift Cylinder

in Field Configuration

15553

Summary of Contents for 3S-3000-3210























































































































Reviews:

No comments

Related manuals for 3S-3000-3210

Belco Tar River DRL-048 Operator'S Manual preview
Tar River DRL-048
Brand: Belco Pages: 23

Brands by name

Popular brands

Load more brands