GREAT PLAINS 3S-3000-3210 Operator'S Manual Download Page 43

Page: 43 / 118

3S-3000/F/HD/HDF

Table of Contents

Index

Operating Instructions

2018-06-18

Table of Contents

Index

195-441M

Using Fertilizer Compartment

Refer to “

Loading Materials

” on page 36 and see

“

Loading Fertilizer Compartment

” on page 37.

Seeding with Both Compartments

Clean out boxes. See “

Main Seed Box Clean-Out

”

on page 66 and “

Fertilizer Box Clean-Out

” on

page 66.

Refer to Figure 34

Open seed/fertilizer flap between seed and fertilizer
compartments. To open the seed/fertilizer flap,
loosen knobs

. Loosen knobs until bent clips can

be turned away from seed/fertilizer flap

When all bent clips have been turned, lift vinyl dew
shield (not shown) and flip the seed/fertilizer flap
rearward over fertilizer tray openings

Refer to Figure 35

With seed/fertilizer flap

covering fertilizer

openings, lower vinyl dew shield

to hold

seed/fertilizer flap over fertilizer openings and away
from divider.

To avoid unnecessary wear, remove the chain from
the clutch shaft to the fertilizer drive.

Figure 34

Open Seed/Fertilizer Flap

16383

Figure 35

Seed/Fertilizer Flap Secured

16380

Summary of Contents for 3S-3000-3210























































































































Search results

Summary of Contents for 3S-3000-3210

Reviews:

Related manuals for 3S-3000-3210

Brands by name

Popular brands

GREAT PLAINS 3S-3000-3210, Operator'S Manual

Search results

Summary of Contents for 3S-3000-3210

Reviews:

Related manuals for 3S-3000-3210

Brands by name

Popular brands