GREAT PLAINS 3S-3000-3210 Operator'S Manual Download Page 32

Page: 32 / 118

2018-06-18

Table of Contents

Index

195-441M

3S-3000/F/HD/HDF

Table of Contents

Index

Operating Instructions

Transport

Loss of Control Hazard:

Towing the drill at high speeds or with a vehicle that is not
heavy enough could lead to loss of vehicle control. Loss of
vehicle control could lead to serious road accidents, injury
and death. To reduce the hazard:

Do not exceed 20 mph (32 kph).

Do not tow a drill that, when fully loaded, weighs more than
1.5 times the weight of the towing vehicle.

In the following table, multiply the total drill weight by
0.67 (



) to determine minimum tractor weight.

Weights for Tractor Requirements

Marker Transportation

Refer to Figure 19

Always transport markers folded flat. Make sure second
marker section rests securely on transport carrier.

Drill Weight (Pounds / Kilograms)

Drill Model

3S-3000-6006

3S-3000HD-6006

3S-3000-4875

3S-3000HD-4875

3S-3000-3610

3S-3000HD-3610

Standard “

” or “

” Drill

12447 lbs / 5646 kg

12425 lbs / 5636 kg

12409 lbs / 5629 kg

For “

” or “

HDF

” Model, add...

+1051 lbs / +477 kg

+1029 lbs / +467 kg

+1007 lbs / +457 kg

With Single Markers, add...

+456 lbs / +207 kg

With Dual Markers, add...

+887 lbs / +402 kg

For Full Main Box Seed Load, add...

+5933 lbs / +2691 kg

Small Seeds

+852 lbs / +387 kg

+832 lbs / +377 kg

+812 lbs / +368 kg

Maximum Configuration: (HDF, Dual

Markers, Seed Loaded, Point Row

Option, 2-Outlet Option)

20464 lbs / 9283 kg

20420 lbs / 9262 kg

20383 lbs / 9245 kg

Figure 19

Marker in Transport Cradle

18857

Summary of Contents for 3S-3000-3210























































































































Search results

Summary of Contents for 3S-3000-3210

Reviews:

Related manuals for 3S-3000-3210

Brands by name

Popular brands

GREAT PLAINS 3S-3000-3210, Operator'S Manual

Search results

Summary of Contents for 3S-3000-3210

Reviews:

Related manuals for 3S-3000-3210

Brands by name

Popular brands