manualshive.com logo in svg

GREAT PLAINS 1510P, Operator'S Manual

Share
Download
GREAT PLAINS 1510P Operator'S Manual Download Page 75

1510P & 1520P

Table of Contents

Index

Options

Great Plains

 | 118-732M | 4/4/19

Table of Contents

Index

71

Separator and Fertilizer Tube 
Weldment

Separator and fertilizer tube weldments are available for
the application of liquid starter fertilizer.

To order the Separator and Fertilizer Tube Weldments,
contact your Great Plains dealer.

20 Series Precision Opener Side 
Depth Wheel Scraper

To order the opener wheel scraper, contact your Great
Plains dealer.

Veris Drive 

The Veris Drive is a precision population controller which
uses a hydraulic drive to accurately drive the metering
system. 

For Information on how to operate the Veris Drive refer to
the Veris Drive section starting on page 73. 

For information on ordering the Veris Drive contact your
Great Plains dealer. 

Separator and Fertilizer Tube
Weldment Package

Part Number

2001 and Before 10 Series 
Openers
All 20 Series Openers

122-257H

2002 10 Series Openers

122-258H

Scraper Packages

Part Number

20P Side Wheel Scraper Kit 

198-960A

19710 

20262 

19977 

Summary of Contents for 1510P



















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands