GREAT PLAINS 1510P Operator'S Manual Download Page 73

Page: 73 / 146

1510P & 1520P

Table of Contents

Index

Options

Great Plains

| 118-732M | 4/4/19

Table of Contents

Index

DICKEY-john

Monitor

The DICKEY-john

Monitor option is a micro-processor

based monitoring system. If seed is not going to the
ground, the monitor will sound and indicate which meter
has stopped planting. The system also provides
information for seed spacing, seed population, area,
ground speed and the projected area/hr.

Harrow Attachment

The coil-tine harrow finishes no-till surfaces by leveling
and distributing residue for enhanced seed emergence.

For information on how to adjust the harrow, refer to
“Harrow Adjustment”, page 48.

To order the harrow attachment, contact your Great
Plains dealer.

Harrow Packages

Part Number

Harrow 116-203A

15848

18411

Summary of Contents for 1510P



















































































































































Search results

Summary of Contents for 1510P

Reviews:

Brands by name

Popular brands

GREAT PLAINS 1510P, Operator'S Manual

Search results

Summary of Contents for 1510P

Reviews:

Brands by name

Popular brands