manualshive.com logo in svg

GREAT PLAINS 1510P, Operator'S Manual

Share
Download
GREAT PLAINS 1510P Operator'S Manual Download Page 40

Great Plains

 | 118-732M | 4/4/19

Table of Contents

Index

36

1510P & 1520P

Table of Contents

Index

Adjustments

Refer to Figure 40

4.

Pull seed meter wheel out about 

1

/

4

 inch, or past

the wheel drive pin, and spin backward to clean out
seeds from top pockets.

5.

Remove seed meter wheel.

NOTE: With the seed meter wheel removed, you

may want to check the meter for internal damage or

trash.

Refer to Figure 41

6.

Place new wheel on meter wheel shaft and push
meter slide retaining clip forward while pushing in
seed meter wheel.

Refer to Figure 42

7.

Be sure slots in the center of seed meter wheel are
aligned with the wheel drive pin on the meter shaft.

Figure 40 

Remove Seed Meter Wheel

18295

S

pi

n 

W

he

el

 

ba

ck

w

ar

d 

be

fo

re

re

m

ov

in

g

Wheel
Drive Pin

18296

Retaining
Clip

Figure 41 

Place New Seed Meter Wheel on Wheel Shaft

18299

Figure 42

Position Seed Meter Wheel

Wheel
Drive Pin

Summary of Contents for 1510P



















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands