manualshive.com logo in svg

GRE KWOV436, Instruction Manual, Page: 42 / 64

Share
Download
GRE KWOV436 Instruction Manual Download Page 42

42

Liner

REFILLING FITTING

• The liner should be well-tensed. Continue with the installation until the water reaches 10 

cm below the refilling fitting.

Cutting of the liner:

A

 • From outside of the pool, locate the centre of the nozzle and mark it using a cutter.

B

 • From inside the pool, mark a small cross on the mark left by the cutter.

C

 • Centre the connector tube over this cross and trace the perimeter. This is automatically 

below the hole of the nozzle in the wood.

D

 • Cut out the traced line with the cutter.

Assembly of the nozzle:

• Hold the body of the nozzle and the first flat seal  with one hand and with other the 

cork seal and the second flat seal.

• From outside of the pool introduce through the hole of the nozzle the flat seal and the 

cork one together, centring them regarding the axis of the hole (the cork seal on the 

wood side).

ATTENTION: hold the seals so they do not drop between the liner and the wood.

• From inside the pool, introduce the .nozzle with the flat seal into the hole. The body of 

the nozzle should be the introduced into the hole of the liner, the second flat seal, the 

cork seal and the hole in the wood.

• Finish the installation of the nozzle by screwing from the outside the nut of the body 

of the nozzle (the flat side against the wood). Reasonably tighten, without forcing too 

much. to fix the liner between the two flat seals.

• Position the flange and screw it.

• Thread the connector tube previously prepared with Teflon (not included) into the 

body of the nozzle, from outside of the pool.

• Temporarily connect the filter tube to the connector tube (see filter chapter) and 

position the free above the water level to continue filling the water for the assembly of 

the skimmer without water coming out of the nozzle.

A

B

C

D

Flange

Body of the nozzle:

Round flat seal

Cork seal

Ball unit

Wood

Nozzle body nut

Connector tube

Look for us in our YouTube 

channel to help you with 

the assembly.

REFILLING FITTING

Install the 

filter before 

continuing 

with cutting 

the liner.

Summary of Contents for KWOV436

































































Reviews:

No comments