manualshive.com logo in svg

Gravely 991001-008, Service Manual

Share
Download
Gravely 991001-008 Service Manual Download Page 29

8 - 29

Standard on Promaster 160 and 200

The mower lift system consists of the mower frame 
with caster wheels, the hydraulic pump and reservoir, 
and the hydraulic lift cylinder with linkage.

8.1  MOWER FRAME

To remove mower frame, Figure 17:

1. Remove mower deck.

2. Disconnect the hydraulic cylinder from the lift arm 

weldment.

3. Pull the pin at the rear center pivot.

4. The frame can be moved forward off the center 

pivot and pulled out.

5. Install in reverse order

8.2  CHECK CASTER WHEELS FOR WEAR

To  replace caster bushings:

1. Pull cotter pin at top of shaft.

2. Drop caster out from the bottom.

3. Clean shaft and grease.

4. Replace washers and bushings and reassemble.

5. Apply grease.

8.3  TO REPLACE WHEEL AXLE

1. Remove nut from axle bolt and pull axle bolt out.  

Inspect roller bearing.  Clean roller and replace if 
needed.

2. Grease axle bolt, roller, and wheel hub.

3. Reassemble axle.  Tighten locking nut to remove 

play but allow wheel to turn.

8.4  LINKAGE

Inspect lift linkage for wear.  Replace bushings by 
removing the lift arm weldment and sliding the old 
bushing out.

8.5  HYDRAULIC SYSTEM

SECTION 8 - MOWER LIFT SYSTEM

PF1980

Figure 17

1. Mower Lift Shaft Weldment
2. Klik Pin

3. Mower Frame Mounting
4. Hydraulic Cylinder
5. Lift Arm Weldment

1

2

2

3

3

4

1

50" Mower

60" Mower

Summary of Contents for 991001-008

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands