manualshive.com logo in svg

Gravely 991001-008, Service Manual

Share
Download
Gravely 991001-008 Service Manual Download Page 16

4 - 16

4.2  FILLING THE FUEL TANK

Add fuel to the fuel tank as needed. See your engine 
manual for the correct type and grade of fuel to be 
used.

1. Put the unit in an open and well ventilated area 

prior to refueling. 

2. Stop the engine.

3. Allow the engine to cool.

4. Clean the fuel cap and in the area around the fuel 

cap. Remove the cap from the fuel tank.

5. Fill the fuel tank with the proper grade of fuel 

recommended by the engine manufacturer. Be 
careful not to spill any fuel.

6. Install fuel cap on the fuel tank and tighten.

7. Clean up any spilled fuel before starting engine.

ENGINE WILL NOT

START UNLESS

   THE PTO CONTROL  IS IN

   THE OFF POSITION

   THE T -BAR CONROL LEVERS

   ARE IN THE NEUTRAL POSITION

CONFORMS TO  ANSI
B71.4  SAFETY  STANDARD
COMMERCIAL TURF
CARE EQUIPMENT.

N

N

SAFETY FIRST

MADE IN THE U.S.A.

SPECIAL TRAINING  NECESSARY.
READ OWNER'S MANUALS BEFORE OPERA

TING

OR SERVICING.
KEEP ALL GUARDS AND SHIELDS IN PLACE.
NEVER PERMIT CHILDREN TO OPERATE.
LOOK FOR PEOPLE AND HAZARDS.
BEFORE LEAVING THE OPERATOR POSITION:

– PUT PTO CONTROL IN THE OFF
   POSITION.
– REMOVE IGNITION KEY.

!

CAUTION

CAUTION

DO NOT PARK ON
SLOPES UNLESS
WHEELS ARE
CHOCKED

N

N

Figure 3

1

2

3

4

5

8

1. Twin T-Bar Control Levers
2. Throttle Lever
3. Choke Lever
4. Ignition Switch
5. PTO Switch

6. Mower Lift Switch
7. Parking Brake Lever
8. Oil Pressure Light
9. Coolant Temperature Light (Kawasaki)
10.Throttle Choke Lever (Kawasaki)

OF1090

991 Series

992 Series

WARNING: Use caution with fuel. Fuel is very 
flammable. Keep fuel in a clean and tight 
container. Keep fuel away from fire and heat. 
Never put fuel in the fuel tank while the engine 
is running or hot. Clean up any spilled fuel 
before starting the engine.

Summary of Contents for 991001-008

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands