manualshive.com logo in svg

Gravely 991001-008, Service Manual

Share
Download
Gravely 991001-008 Service Manual Download Page 24

7 - 24

 

7.1  REPLACING MOWER BELT

NOTE: The following procedure applies to both the 
long mower belt and the short mower belt.

1. Stop the engine.  Remove the ignition key.

2. Remove the footboard from the support frame.

3. Loosen and remove the two nuts, the flat washer 

and the spring from the idler rod and remove the 
old belt.

4. Arrange the new mower belt on the spindle 

sheaves and the idler pulley.  Put the belt on the 
mower clutch sheave (long mower belt only).  Put 
the idler rod back through the spring support.  Put 
the spring, flat washer and two nuts back on the 
idler rod.  See Figure 10.

5. Set mower cut height to 3.5 inches and adjust belt.  

To tighten the mower belt, turn the adjusting nut on 
the idler rod until the gap between the coils of the 
spring is .010" to .015" (.25 mm to .38 mm).  When 
the belt is tight, hold the adjusting nut and lock the 
jam nut against it.

6. Put the foot board back on the support frame.

7.2  MOWER BLADE

Regularly check mower blades for wear and that lock 
washer is fully compressed by cap screw(s) (requires 
25-30 ft-lbs (33.8-40.6 Nm) of torque on cap screw).

When blade needs sharpening, block blade to prevent 
rotation and remove cap screw(s), lock washer(s) and 
blade from shaft.

Sharpen both edges of blade at original angle (25

o

), 

removing equal amounts of material from each end to 
maintain proper blade balance.  New blades are 
balanced to within 1.3 in-lbs (0.14 Nm) at factory.  DO 
NOT grind around corner at tip of blade.  If cutting edge 
of blade cannot be sharpened in a straight line to within 
1/8 of an inch of its end, replace blade. Use Gravely 
replacement blade only.

SECTION 7 - MOWER DECK

Figure 10

1. Long Mower Belt
2. Short Mower Belt
3. Idler Rod

4. Spring
5. Jam Nut
6. Adjusting Nut

PF3000

PF2090

1

2

3

3

4

4

5

5

6

6

1

2

3

3

4

4

5

5

6

6

7

7

7

CAUTION: Use sturdy gloves or padding to 
protect hands when working with mower 
blades.

OM0240

Figure 11

1. Cutting Edge
2. Square Corner
3. Air Lift Erosion

4. Air Lift
5. Reverse Lift

1

2

3

4

Summary of Contents for 991001-008

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands