GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY
#0060376
Keine Haftung für Druckfehler. Technische Änderungen vorbehalten! No liability for printing errors. We reserve the right to introduce
modifications. Sous réserve de modifications! Nous ne sommes pas responsables d’éventuelles erreurs d’impression!
03/2009
19
Notes on building the model
•
This model is not intended for the beginner to modelling, and for this reason the instructions do not cover
every single step of construction, as we assume that the experienced model builder will be familiar with
these standard techniques.
•
The version racing MICRO MAGIC Carbon requires more detailed adjustment, because all laser-cut and
vacuum-moulded parts – except the canopy, which fits exactly, have been adjusted to the normal version,
racing MICRO MAGIC. But this work can be easily done by the modeller himself.
•
We recommend that you visit the Internet website www.micromagic.info for the latest information on
assembling and setting up the model.
•
If you do not understand the technical terms relating to sailing boats, you can download a sketch showing
the basic terminology from the Internet site mentioned above.
•
Before you start building the boat, please take the time to study the plan and read right through the
instructions, referring constantly to the Parts List. In general terms the instructions and parts list reflect the
sequence of assembly.
•
The laser-cut wooden components are retained in their sheets by small lugs. Cut them through from both
sides using a sharp knife, then break the parts away from the waste material.
•
All the laser-cut parts have a black outline caused by the cutting process. You can easily sand this off if
you wish.
•
The wooden internal parts for the hull are accurately pre-cut, but it is still important to trim them to match
the shape of the hull and deck precisely. If the bulkheads are a tight fit, they will show through on the
outside of the hull, so it is important to trim the parts as carefully and as accurately as you can.
•
TIP:
the rigging cord is easier to thread through small holes and openings if you first apply a drop of cyano
to the end to harden it, then cut off the frayed extremity.
•
Compare the laser-cut parts with the sketches at the end of these instructions to help you identify them
and assign the part numbers.
•
Wooden parts which have been coated with GLATTFIX sanding sealer cannot be glued satisfactorily using
UHU acrylit or STABILIT express, so keep the sealer away from the joint areas. You should also avoid
smearing excess adhesive onto the model’s surfaces, as this will often prevent paint adhering properly.
This applies in particular when you are gluing the vacuum-moulded plastic parts.
•
Please bear in mind that many tools can be dangerous if misused or handled carelessly.
•
Deploy the receiver aerial as high up in the hull as possible. Reception will be very poor if it is positioned
below the waterline, and effective range will be greatly reduced.
•
It is important to clean the joint surfaces carefully before gluing parts together. This is best done by
sanding lightly, followed by wiping with a non-greasy liquid detergent or methylated spirit (“meths”). The
same applies to all surfaces which are to be painted, as this improves the paint’s adhesion considerably.
•
Recommended adhesives for joining particular materials:
Material – material
Suitable adhesives
Metal – metal
Cyano-acrylate, UHU plus
ABS – wood
Cyano-acrylate, UHU acrylit
ABS – ABS
Cyano-acrylate, UHU acrylit, UHU plast spezial
ABS – metal
Cyano-acrylate, UHU acrylit
Wood – wood
Cyano-acrylate, UHU hart, white glue
Wood – metal
Stabilit express
Read the instructions supplied with the adhesives. Be sure to observe any special notes in the instructions regarding particular
adhesives. If you are using acetone, methylated spirits or any other solvent as a cleaning agent, special safety measures are
necessary. Read the instructions supplied with these materials.
