background image

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY

 

We reserve the right to introduce modifications. Not liable for printing errors!               

12/2011

 

21 

  Never fly directly towards people. 

  Make sure to keep a safe distance from residential areas: at least 1.5 km “as 

the crow flies”.  It is always best to join a club and fly at the approved model 
flying site. Always keep well clear of high-tension overhead cables.
 

  Whenever working on the engine, make sure that  you have secure footing, 

and always hold the model securely.  

  When  starting  and  landing,  the  take-off  and  landing  strips  should  be  kept 

free of unauthorised people and movable obstacles. 

  The model aircraft must be kept constantly in sight during the entire flight. It 

must always give way to manned aircraft. 

  Never  operate  your  aircraft  from  public  roads,  squares,  squares,  school 

playgrounds,  parks,  or  sports  grounds,  et  cetera,  and  ensure  that  you  are 
always in full control of the model.
 

  To  ensure  that  you  can  stop  your  engine  at  any  time,  the  throttle  must  be 

adjusted so that  the  carburettor barrel closes completely when the throttle 
stick and trim are moved to their end points. If this does not work, pinch the 
fuel  line  between  your  fingers  or  pull  off  the  connecting  tube  to  the  tank. 
Never try to stop the engine by grasping the flywheel, propeller, or spinner! 

  All model fliers should take care to ensure that the public safety, especially 

that  of  people  and  property,  as  well  as  orderly  flying  operations,  are  not 
endangered or disturbed.
 

  In legal terms, model aircraft are classed as aircraft and as such are subject 

to legal regulations and restrictions that must be observed. 

  The brochure “Modellflugrecht, Paragrafen and mehr” (Model Aviation Law, 

Legal Requirements and more), Order No. 8034.02 contains a summary of all 
these rules, and your local model shop should also have a copy which you 
can read. For models with internal combustion engines, it is necessary, for 
example,  to  have  the  landowner's  permission  for  flights,  and  insurance  is 
also  mandatory.    There  are  also  regulations  concerning  your  radio  control 
system that must be observed.
 

  These notes are intended only to make you aware of the many dangers and 

hazards  that  can  arise  if  you  work  carelessly  or  irresponsibly.  If  you  take 
reasonable care, model flying is a highly creative, instructive, and relaxing 
pastime.
 

  The  extensively  pre-fabricated  model  can  be  built  in  a  very  short  time. 

However, the remaining steps are important and have to be carried out with 
care. Doing this work properly determines whether the model will have the 
prescribed  rigidity  and  flight  characteristics;  so  please  work  slowly  and 
precisely!
 

   

Important safety notes 
You have acquired a kit that can be assembled into a fully working RC model when 
fitted  out  with  suitable  accessories.  However,  GRAUPNER  has  no  control  over 
whether you observe the instructions for the installation and operation of the model or 
the  use  and  maintenance  of  the  associated  components.  For  this  reason 
GRAUPNER assumes no liability for loss, damage, or costs, which are incurred due 
to the incorrect use of our products or due to improper behaviour on the part of the 
user,  or  which  are  connected  with  such  operation  in  any  way.    Unless  otherwise 

Summary of Contents for BO 209 MONSUN

























Reviews: