Graco Therm-O-Flow Plus, Instructions Manual

Page: 80 / 82

80 309085
Accessories
233095 Automatic Crossover Kit
Switches operation of one pump to a
second pump. Includes low level
switches, lights and control for preheat
and automatic drum cross–over.
Powered from LS connector of control
panel. Requires 233098 Pendant.
233096 Low Level Drum Signal Kit
Includes switch and bracket and lights a
red beacon when drum is empty.
C34220 Hose Support Kit for 165 mm Pneu-
matic Ram
Includes hose spring support and brack-
et to prevent hose kinks. Use for second
heated hose.
918461 Hose Support Kit for 165 mm Hydrau-
lic Ram
Includes hose spring support and brack-
et to prevent hose kinks. Use for second
heated hose.
C34130 Hose Hanger Kit
Includes hose spring support and brack-
et for hanging.
243697 Heated Manifold
Includes (2) 3/4 npt(f) inlet check valves,
1 npt 4–posted manifold, (2) 1 in. npt(f)
outlet gate valves, mounting bracket,
400w 230 VAC heaters, RTD sensor and
8 pin connector box.
243279 “T” Wiper Kit
Includes both wipers and all band
clamps.
C32451 Vent Hood Kit
Mounts to rear of ram and used to vent
fumes. Use for ram pumps without vent
hood for dispensing PUR materials.
233097 Inactivity Timer Kit
Set to shut off unit if there is no pump ac-
tivity within a given time.
918397 Drum Clam Shell
Used to reinforce fiber drums when on
the pump ram.
918395 Heavy Duty Drum Clamp
Centers, supports, and holds drum dur-
ing ram removal.
C32463 Saddle Clamps
Locates drum on base for raising and
lowering of ram.
243275 Drip Tray Kit
Includes drip tray shield and two brack-
ets which mount on the ram cylinders to
catch material drips when changing
drums.
115694 Drip Tray Shield
Used with 243275, to retain any material
drips from heated plates.
233098 Pendant Control with 7–day Timer
Plugs into any Therm–O–Flow Plus
6–/8–zone control box.
Part No. Accessory Controllers and Cables
243698
2–Zone (self–tuning PID) control box for adding one hose (up to 15 ft) and one heated accessory. 230 volt
plug, 25 amp, (2) 16 pin connectors. Note: Cable needed to connect to remote devices.
243699 4–Zone (self–tuning PID) control box for adding two hoses (up to 15 ft) and two heated accessories. 230 volt
plug, 25 amp, (2) 16 pin connectors. Note: Cable needed to connect to remote devices.
196313
15 ft cable, 16 pin to 16 pin extension cable. Runs between controller and heated hose.
196314
25 ft cable, 16 pin to 16 pin extension cable. Runs between controller and heated hose.
196315
15 ft cable, 16 pin to 8 pin extension cable. Runs between controller and heated accessory.
196316
25 ft cable, 16 pin to 8 pin extension cable. Runs between controller and heated accessory.
196317 15 ft cable, 16 pin to (2) 8 pin extension cable. Runs between controller and heated devices.
196318 25 ft cable, 16 pin to (2) 8 pin extension cable. Runs between controller and heated devices.
116159 25 ft cable, for communications from drum unloader control to Therm–O–Flow Plus accessory zone controls
(2–zone 243698 and 4–zone 243699). (Connects to PN connector of controls.)
Part No. Miscellaneous Accessories
C58942
120 volt AC solenoid kit for heated double–acting air–operated valves. Includes solenoid, 61 cm high temp.
Air tubes, air fittings and muffler.
C59038 24 volt DC solenoid kit for heated double–acting air–operated valves. Includes solenoid, 61 cm high temp.
Air tubes, air fittings and muffler.
243703
240 volt AC solenoid kit for heated double–acting air–operated valves. Includes solenoid, 61 cm high temp.
Air tubes, air fittings and muffler.