Graco GM 3500 Instructions And Parts List Download Page 36

Page: 36 / 44

Parts – Pressure Control

Part No. 222–369 – Replacement Pressure Control forAll GM3500 Sprayers

Part No. 222–369 includes all items marked with a

[

. It does not include unmarked items.

For Upright sprayers, order the Basic Control, 222–369, and/or items 309, 312, 313, and 314 as needed.

For the Lo–Boy sprayers, order the Basic Control, 222–369, and items 309 and/or 322 as needed.

Ref
No.

Part No.

Description

Qty

Ref
No.

Part No.

Description

Qty

300

222–380

[

PRESSURE CONTROL
Includes items 302 to 304

301

183–466

[

LABEL, warning

302

105–679

[

ON/OFF SWITCH

303

105–659

[

BOOT, switch

304

107–255

[

GUARD, locking

305

157–021

[

LOCKWASHER, No. 8, internal

306

100–284

[

NUT, hex, msc 8–32 UNC–2a

307

108–219

[

RECTIFIER, bridge

308

220–979

[

CONDUCTOR, red

309

220–978

CONDUCTOR, red, white,black

310

100–035

[

SCREW, mach, slotted pan hd,
No. 8 x 5/16”

311

108–783

[

SCREW, mach, flat hd; 8–32
x 0.812”

312

162–453

NIPPLE, hex, 1/4–18 npsm

313

108–852

CONNECTOR, 45

314

100–840

ELBOW, str, 1/4–18 npt(m x f)

316

222–352

[

TRIAC

317

107–070

[

SCREW, flat head

318

100–072

[

NUT, hex

319

103–181

[

LOCKWASHER

320

101–754

[

PLUG, pipe

322

109–106

UNION, swivel, 45

324

101–754

[

PLUG

Replacement Danger and W

arning labels, tags and cards

are available at no cost.

–

RED

MAIN
SWITCH

MT2

MT1

WHITE

RED

WHITE

BLACK

CLUTCH
FIELD

GROUND

RECTIFIER

ADJUSTABLE
PRESSURE
SWITCH

ENGINE

WIRING SCHEMATIC

Summary of Contents for GM 3500













































Search results

Summary of Contents for GM 3500

Reviews:

Related manuals for GM 3500

Brands by name

Popular brands

Graco GM 3500, Instructions And Parts List

Search results

Summary of Contents for GM 3500

Reviews:

Related manuals for GM 3500

Brands by name

Popular brands