Graco GM 3500 Instructions And Parts List Download Page 14

Page: 14 / 44

307-863

Troubleshooting

PROBLEM

CAUSE

SOLUTION

Displacement pump output
low on upstroke

Pump inlet screen clogged

Clean.

Piston ball check not seating

Service piston ball check. See page 18.

Piston packings worn or damaged

Replace packings. See page 18.

Sleeve gasket in displacement
pump worn or damaged

Replace. See page 18.

Displacement pump output
low on downstroke or both
strokes

Pump inlet screen clogged

Clean.

Piston packings worn or damaged

Replace packings. See page 18.

Intake valve ball check not seating
properly

Clean and service. See page 18.

Engine RPM too low

Increase throttle setting. See Startup,
Step 11, page 10.

Clutch worn or damaged

Replace. See page 24.

Paint leaks into wet–cup

Loose wet–cup

Tighten just enough to stop leakage.

Throat packings worn or damaged

Replace packings. See page 18.

Displacement rod worn or
damaged

Replace rod. See page 18.

Low fluid delivery

Pump inlet screen clogged.

Clean.

Pressure setting too low

Increase pressure. See Startup,
Step 11, page 10.

Engine RPM too low

Increase throttle setting. See Startup,
Step 11, page 10.

Dirty outlet filter, tip filter or tip

Clean.

Large pressure drop in hose

Use larger diameter hose.

Spitting from gun

Air in fluid pump or hose

Check for loose connections at pump in-
take and tighten. Them prime the pump.
See Startup, page 10.

Tip partially clogged

Clear.

Fluid supply is low or empty

Refill and prime the pump. See Startup,
page 10. Check fluid supply often to pre-
vent running the pump dry.

Summary of Contents for GM 3500













































Search results

Summary of Contents for GM 3500

Reviews:

Related manuals for GM 3500

Brands by name

Popular brands

Graco GM 3500, Instructions And Parts List

Search results

Summary of Contents for GM 3500

Reviews:

Related manuals for GM 3500

Brands by name

Popular brands