Graco GM 3500 Instructions And Parts List Download Page 13 | Manualshive

Page: 13 / 44

background image

13

307-863

Troubleshooting

WARNING

To reduce the risk of serious bodily injury always
follow the Pressure Relief Procedure Warning on
page 2 before checking, adjusting, cleaning or
shutting down the sprayer.

Check everything in the chart before disassembling the sprayer.

(Continued on page 14)

PROBLEM

CAUSE

SOLUTION

Engine/sprayer won’t start

Engine switch not on

Turn on.

Out of gas

Replenish

Engine oil level low

Try starting engine. If light on rear of en-
gine glows, replenish oil.

Spark plug cable disconnected or
spark plug damaged

Connect cable on top of engine or re-
place spark plug. See Fig. 3, page 11.

Water frozen in pressure control

Return pressure control to authorized
Graco dealer for repair.

Engine won’t “pull over”

Oil seepage into combustion
chamber

Remove spark plug. Pull starter rope 3 or
4 times. Clean and replace plug. Try to
start. Keep sprayer upright to avoid oil
leakage. See last CAUTION on page 10.

Engine operates, but dis-
placement pump doesn’t

Pressure control switch turned OFF

Turn on.

Pressure setting too low

Increase pressure.

Displacement pump outlet filter
dirty

Clean filter.

Tip or tip filter clogged

Clean tip or tip filter.

Displacement pump rod seized by
dry paint

Service pump. See page 18.

Connecting rod worn or damaged

Replace. See page 20.

Drive housing worn or damaged

Replace. See page 21.

Electrical power not energizing field

Check wiring connections. See page 16.
With pressure control switch ON and
pressure turned to MAXIMUM, use a test
light to check continuity across black and
white wires from pressure control.
Have pressure control checked by autho-
rized Graco dealer.

Clutch worn or damaged

Service. See page 24.

Pinion assembly worn or damaged

Service. See page 22.

«
...
11
12
13
14
15
...
»

Summary of Contents for GM 3500













































Reviews:

No comments

Related manuals for GM 3500

Brand: Landoll Pages: 6

Brand: ParaBody Pages: 9

Brand: ParaBody Pages: 3

Brand: MacDon Pages: 45

Brand: H&S Pages: 30

Brand: JAC Pages: 103

Brand: 3Disc Pages: 12

BTL PA0400 Series

Brand: Balluff Pages: 22

Micropulse BTL5 Series

Brand: Balluff Pages: 12

BNI IOW-560-W01-K022

Brand: Balluff Pages: 32

Brand: Baltic Pages: 68

Brand: Baltic Pages: 68

Max Charge MC-612

Brand: Balmar Pages: 12

BTL PA0400 Series

Brand: Balluff Pages: 204

Brand: Datex-Ohmeda Pages: 80

Brand: MacDon Pages: 2

Brand: V-TAC Pages: 6

Brand: Launch Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands