PELIGRO POR MAL USO DEL EQUIPO
Seguridad general
Cualquier mal uso del equipo pulverizador o los accesorios, tal
como sobre presurización, modificación de piezas, uso de ma-
teriales y productos químicos incompatibles, o utilización de
piezas dañadas o desgastadas, puede hacen que se rompan
y causen la inyección de fluido u otras lesiones corporales gra-
ves, incendio, explosión o daños a la propiedad.
Siempre usar gafas, guantes, vestimentas protectoras y un res-
piradero, tal como recomiendan los fabricantes del fluido y del
solvente.
Presión del sistema
Esta pulverizadora puede desarrollar 210 barías (3000 psi) de
PRESION DE TRABAJO MAXIMA. Asegurar que todo el equi-
po pulverizador y sus accesorios tienen la capacidad para
aguantar la presión máxima de trabajo de ningún componente
o accesorio de este sistema.
Compatibilidad de fluido
Siempre leer las instrucciones del fabricante del fluido y solven-
te antes de usarlos en esta pulverizadora.
PELIGRO POR MAL USO DEL EQUIPO
El fluido que escapa a alta presión por las mangueras puede
ser muy peligroso. Si en la manguera se desarrola un escape,
una rotura o rajadura debido a cualquier tipo de desgaste, daño
o maltrato, el chorro a alta presión emitido por allí puede causar
una lesión por inyección u otras lesiones corporales graves o
daños a la propiedad.
¡Todas las mangueras para fluidos tienen que tener
guardas de resorte en ambos extremos! Estas protegen las
mangueras contra dobleces o retorceduras en los acoplamien-
tos o cerca de ellos, los que podrían traducirse en roturas de la
manguera.
Antes de usarlas, APRETAR bien firmes todas las conexiones.
El fluido a lata presión puede desalojar un acoplamiento suelto
o dejar que pro él escape un chorro a alta presión.
NUNCA usar una manguera que está dañada. Siempre revisar-
la en busca de cortaduras, escapes, abrasión, cubierta abulta-
da, o acoplamientos sueltos o dañados. Si llegara a encontrar-
se cualquiera de estas condiciones, reemplazar de inmediato
la manguera. NO intentar reacoplar una manguera de alta pre-
sión o enmendarla con cinta adhesiva u otro material similar.
Una manguera que ha sido remendada no aguante el fluido al
alta presión.
Manejar y pasar cuidadosamente las mangueras. No tirar de
las mangueras para mover el equipo. No usar fluidos o solven-
tes que sean incompatibles con el tubo interno y la cubierta de
la manguera. NO exponer las mangueras a temperaturas sobre
82
)
C (180
_
F) o bajo -40
_
C (-40
_
F).
Continuidad del circuito de puesta a tierra
de la manguera
La continuidad del circuito de puesta a tierra apropiado es
esencial para mantener conectado a tierra el sistema pulveriza-
dor. Es indispensable revisar la resistencia eléctrica máxima de
las mangueras de aire y de fluido por lo menos una vez a la se-
mana. Si la manguera no tiene una etiqueta en la cual se espe-
cifica la resistencia eléctrica máximum, ponerse en contacto
con el proveedor o fabricante de la manguera para la informa-
ción sobre los límites de resistencia. Usar un metro de resisten-
cia en la gama apropiada para comprobar la resistencia; si ex-
cede los lites recomendados, reemplazarla de inmediato. Es
muy arriesgado tener una manguera sin puesta a tierra o con
la puesta a tierra en malas condiciones. Leer también la infor-
mación sobre RIESGO DE INCENDIO O EXPLOSION, más
arriba.
PELIGRO DE INCENDIO O EXPLOSION
El flujo a alta velocidad del fluido al pasar por la bomba y man-
guera crea electricidad estática. Si todas las partes del equipo
pulverizador no tienen buena tierra, pueden ocurrir chispas,
convirtiéndo al sistema en algo peligroso. También, pueden
producirse chispas al enchufar o desenchufar el cordón eléctri-
co o al usar un motor de gasolina. Estas chispas pueden infla-
mar los vapores de los solventes y el chorro de fluido pulveriza-
do, partículas de polvo y otras sustancias inflamables, sea al
aire libre o bajo techo, lo que podría causar una explosión o in-
cendio y graves lesiones corporales y daños a la propiedad.
Si ocurre una chispa de electricidad estática o incluso un ligero
choque eléctrico mientras se usa el equipo, DEJAR DE PULVE-
RIZAR DE INMEDIATO. Revisar todo el sistema en busca de
una tierra apropiado. No usar de nuevo el sistema hasta haber
identificado y solucionado el problema.
Puesta a tierra
Para reducir el riesgo de chispas estáticas, conectar a tierra la
pulverizadora y todo el otro equipo de pulverizar que se use o
se encuentre en el lugar que se va a rociar. CONSULTAR el có-
digo eléctrico de la localidad para las instrucciones sobre las
conexiones a tierra exigidas para la zona y tipo de equipo. ASE-
GURAR de conectar a tierra todo este equipo pulverizador:
1.
Pulverizadora: Conectar el alambre de tierra y la abrazadera
(suministrada) a una buena conexión a tierra.
2.
Mangueras para fluidos: usar solamente mangueras con
puesta a tierra de una longitud combinada de 150 m (500
pies), para asegurar buena continuidad a tierra. Referirse
también al párrafo sobre continuidad a tierra de la manguera.
3.
Pistola: hacer la puesta a tierra conectándola a una mangue-
ra de fluido y pulverizadora bien conectadas a tierra.
4.
Suministrar un recipiente: de acuerdo al código local. Usar
solamente baldes de metal, que sean conductivos. No colo-
car el balde en una superficie no conductiva, como papel o
cartón, que interrumpe la continuidad a tierra.
5.
Objeto que se está rociando: de conformidad con el código
local.
6.
Todos los baldes de solvente usados durante el lavado, de
conformidad con el código local.
7.
Para mantener la continuidad a tierra durante el lavado o
arga de presión, siempre apoyar una parte metálica de la pis-
tola bien firme contra el costado de
balde de metal, después
apretar el gatillo.
Seguridad durante el lavado
Para reducir el riesgo de que se inyecte o salpique fluido en la
piel, o que ocurra una descarga de electricidad estática, siem-
pre seguir las INSTRUCCIONES PARA EL LAVADO, dadas en
la página 12. Seguir el Procedimiento de Descarga de
Presión en la página 6, y quitar la
boquilla de metal y usar le
presión más baja posible de fluido durante el lavado.
PRECAUCIONES PARA LOS MOTORES DE GASOLINA
NUNCA llenar el tanque de combustible mientras el motor está
funcionando o caliente. El combustible derramado en una su-
perficie caliente puede encenderse y provocar un incendio.
SIEMPRE verter el combustible lentamente para evitar derra-
mes. Leer PELIGRO DE INCENDIO O EXPLOSION.
NUNCA hacer funcionar el motor en un edificio cerrado sin en–
caminar los gases de escape hacia el aire libre. Los gases de
escape contienen monóxido de carbono, un gas venenoso, sin
olor e invisible que podría causar enfermedades graves, inclu-
so la muerte, al inhalarse.