Graco Dyna-Star 3A6941J Instructions Manual Download

Page: 1 / 54

3A6941J

Instructions

Compact Dyna-Star

Electric Pump

Provides lubricant flow and pressure to operate both single line and series progressive

automatic lubrication systems. For automatic lubrication systems only. For professional

use only.

Not approved for use in explosive atmospheres or hazardous (classified) locations.

3500 psi (24.1MPa, 241 bar) Maximum Working

Pressure

See page 3 for model information.

Related Manuals

3A6932 Compact Dyna-Star Auto-Fill Shut Off Kit

3A6998 Compact Dyna-Star 35 lb (5 Gallon) Kit

3A7035 Compact Dyna-Star Pump Cable

333393 Fill Valve

Important Safety

Instructions

Read all warnings and instructions

in this manual and in your injector

manual before using the

equipment. Save these

instructions.

Summary of Contents for Dyna-Star 3A6941J























































Search results

Summary of Contents for Dyna-Star 3A6941J

Reviews:

Related manuals for Dyna-Star 3A6941J

Brands by name

Popular brands

Graco Dyna-Star 3A6941J, Instructions Manual

Search results

Summary of Contents for Dyna-Star 3A6941J

Reviews:

Related manuals for Dyna-Star 3A6941J

Brands by name

Popular brands