background image

GAS CYLINDER INFORMATION 
1.

This BBQ is designed to be used with a gas cylinder not exceeding 9KG. 

2.

The gas cylinder supply valve must be turned off when the BBQ is not in use. 

3.

Gas cylinders must be stored outdoors, out of reach of children and must not be stored 

in a building, garage or any other enclosed area. 

4.

The gas cylinder used must incorporate a safety collar to protect the valve assembly. 

5.

Never store a spare cylinder under the BBQ shelves or inside the trolley housing. Any 

ULPG  cylinder  not  attached  to  the  BBQ  for  use  should  be  stored  outdoors  and  well 
away from the BBQ. 

IMPORTANT 
1.

When disconnecting and removing the gas cylinder for the purpose of refilling, always 

follow these procedures. 

2.

Ensure  that  all  gas  control  valves  on  the  BBQ  and  the  gas  cylinder  are  turned  off 

before disconnecting the regulator from the cylinder. 

3.

Do not smoke or use a naked flame near the BBQ or gas cylinder while disconnecting 

the gas line between the BBQ and gas cylinder. 

4.

Remove the gas cylinder from the enclosure before disconnecting the regulator from 

the BBQ. 

5.

Tighten all connections before placing the gas cylinder back in to place. 

6.

The  gas  leak  testing  procedure  should  be  conducted  every  time  the  gas  cylinder  is 

refilled  and  reconnected  to  the  BBQ  prior  to  using  the  BBQ  (Procedure  located  on 
Page 2 of this manual). 

Safety Guide 

 

 

 

For safe use of your BBQ and to avoid serious injury: 

DO NOT let children operate or play near the BBQ. 

KEEP BBQ area clear and free from materials that burn.  

DO NOT block holes in bottom or back of BBQ. 

Check burner flames regularly. 

Use  BBQ  in  well-ventilated  space.  NEVER  use  in  enclosed  spaces  such  as  a  carport, 
garage, porch, covered patio, etc. 

DO NOT use charcoal or ceramic briquettes in a gas BBQ. 

Warning 

Page   6   

Summary of Contents for GBQA420









































Reviews: