background image

Safety Guide 

A strong gas smell or hissing sound of escaping gas indicates a serious problem with the 
BBQ or ULPG cylinder. Failure to immediately follow the steps listed below could result 
in a fire or explosion that could cause serious injury, death or property damage. 

Shut off gas supply at cylinder 

Turn the control knobs of the BBQ to the off position 

Extinguish any open flame 

Open the BBQ hood 

Get away from the ULPG cylinder 

Do not try and fix the problem yourself 

If gas odour continues or you cannot extinguish fire, call fire brigade 

 

To prevent fire and smoke damage, remove all packaging material before operating BBQ. 

HOSE ASSEMBLY AND SAFETY 
A leak test 

(Procedure located on Page 2 of this manual) 

must be carried out prior to using the 

BBQ  for  the  first  time  and  each  time  the  gas  cylinder  is  refilled,  or  each  time  the  gas 
hose and gas regulator have been disconnected. Check all gas hose and line connections 
for damage, cuts or cracks each time you use the BBQ. 

If the hose shows signs of deterioration or damage, complete a leak test to identify any 
leaks and if required replace the hose. 

The  hose  must  remain  free  of  kinks  and  sharp  bends.  Never  puncture  or  put  stress  on 
the hose or fittings. Hose connection is located at the lower front area on the right side 
wall of the main body of the BBQ. 

Replacement  hose  and  regulators  can  be  purchased  from  your  local  BBQ  retail 
specialist. Leak Test procedure is located on Page 2 of this manual. 

BURNERS 
The location of the tube burner to the jet is vital for safe operation. Check to assure the 
jets are inside the burner tubes before using the gas BBQ 

SPIDER AND INSECT WEBS 

Some  times  spiders,  ants  and  other  insects 
climb  into  the  tube  burners,  gas  lines  and 
other  areas  of  the  BBQ.  The  insects  can  spin 
webs,  build  nests  and  lay  eggs.  The  webs  or 
nests  can  be  very  small,  but  they  are  very 
strong and can block the flow of gas.  

NOTE: Complications arising from spider and insect webs built up inside gas lines are 
expressly excluded from Warranty

   

To avoid this occurring, clean burners prior to use, after storing, at the beginning of 
your BBQ season or after a period of one month with out use. Guards are on the air 
intakes in an effort to reduce this problem, but it will not eliminate it.   An obstruction 
can result in a “flashback” (a fire in the burner tubes). The burner may still light, but 
the obstruction does not allow full gas flow to the burners. 

Page   5   

Summary of Contents for GBQA420









































Reviews: