background image

 

GJK Assembly Instructions

 

 

 

Grill Assembly  

Instructions 

The GJK 36” Series Grill  Model is almost 
completely factory assembled.
 

Assembly is required for: The locking cast-
ers, side shelves, condiment holders, doors, 
hole plugs, grates and briquets. 
 

Please consult the Owner’s manual for addi-
tional pertinent information regarding im-
portant general safety rules, maintenance, 
troubleshooting, etc.
 

Leak test all gas connections before using. 

Caution: Combustible material should never 
be within 24 inches of the top, bottom, back 
or sides of your MHP Gas Barbecue Grill.

 

 

Step 1: Locking Casters  

(See Fig. 1) 

  The locking casters are packed with the side shelves. 
Lift one end of the grill about 12 inches and block it so 
it won’t fall. Simply push the casters up into the corner 
pocket brackets until they bottom out. Some resis-
tance will be felt so the casters may have to be tapped 
up with a block of wood. They should also bottom out 
when the grill is set back down. The casters are 
locked when the foot tab is in the down position. 

 

 
 
 
 
 
 
 
 

 
 

Step 4: Attaching the Doors  (

Fig. 3)

 

The doors simply drop onto the hinge pins. Hold the door 
in the open position (straight out from the grill front) and 
carefully match the hinge pins to the door hinges and 
push down. 

The bottom catch is magnetic, the top catch is a me-
chanical pull catch. On the inside of the right hand door 
install the wire condiment holder using two (2) 10-24 x 
½” bolts and nuts. Tuck the horizontal wire hooks behind 
the door edge. 

 

Complete View of GJK Grill 

Step 2: Side Shelves  

(See Fig. 2

The side shelves are attached to the main cart with four 
¼ - 20 X ½" bolts and split washers. Simply install one 
(1) upper bolt (w/washer) loosely and let the shelf hang. 
Then lift, pivoting the shelf while the remaining bolts and 
washers are put in and tightened. 
 

Step 3: Condiment Holders  

See Fig. 2

Condiment Holders are attached to the front of the side 
shelves using the two 10-24 x ½" Stainless Steel 
Carriage Bolts and Kep nuts for each holder.

 

Fig. 2 

Summary of Contents for GJK 36 Series






Reviews: