GMC 2002 Safari Owner'S Manual Download Page 65

Page: 65 / 400

1-58

3. Run the vehicle’s safety belt through or around the

restraint. The child restraint instructions will show
you how.

4. Buckle the belt. Make sure the release button is

positioned so you would be able to unbuckle the
safety belt quickly if you ever had to.

5. To tighten the belt, pull its free end while you

push down on the child restraint. If you’re using
a forward

facing child restraint, you may find it

helpful to use your knee to push down on the child
restraint as you tighten the belt.

6. Push and pull the child restraint in different

directions to be sure it is secure.

To remove the child restraint, just unbuckle the vehicle’s
safety belt. It will be ready to work for an adult or larger
child passenger.

Summary of Contents for 2002 Safari
















































































































































































































































































































































































































Search results

Summary of Contents for 2002 Safari

Reviews:

Brands by name

Popular brands

GMC 2002 Safari, Owner'S Manual

Search results

Summary of Contents for 2002 Safari

Reviews:

Brands by name

Popular brands