GMC 2002 Safari Owner'S Manual Download Page 17

Page: 17 / 400

1-10

5. Lift up on the left and the right seat release levers at

the same time. The latches are near the floor on the
rear legs of the seat.

6. Lift up on the rear of the seat to remove the seat

assembly from the rear latch pins. Then, pull back
and lift the seat out of the vehicle.

Your seat release latch lever is operated with a
two

stage mechanism. To fully release the latch,

two levels of lift effort will be required. First,
a low effort to overcome the first stage and then
a moderate effort to fully release the latch.

Summary of Contents for 2002 Safari
















































































































































































































































































































































































































Search results

Summary of Contents for 2002 Safari

Reviews:

Brands by name

Popular brands

GMC 2002 Safari, Owner'S Manual

Search results

Summary of Contents for 2002 Safari

Reviews:

Brands by name

Popular brands