Glutz SD-L F 9365 Series, Mounting And Operating Instructions

Page: 57 / 112

SD‑L F (9365x)
0548-988-11---20_2022.01.indd
0548-988/12
Page 57 of 87
Mounting and operating instructions
7.4.2 Configuration (CONFIG)
Parameter Description Setting range Default
Servo Support for manual push to open
The key opens automatically. Five-position adjustment, depending on the width and weight of the door leaf.
Only usable if DubleD = OFF, Invers = OFF and InterL = OFF.
OFF
1...5
OFF
APuGo Triggering angle Push&Go (angle push&go)
Only usable if Servo = OFF.
OFF
2...10°
OFF
ASES Suppression point Safety Element Stop (angle safety element stop)

see illustration 1)
If Ao is changed, ASES is automatically set to Ao.
45°...Ao 95°
Ao depen -
ding (95°)
ASER Suppression range of the safety element reversing (angle safety element reversing)

see illustration 2) 0...60° 0°
SeOpCo Persistent opening (safety element open continue)
After a Safety Element Stop during the opening procedure, the door shall continue its opening move (instead
of closing), as soon as SES is activated.
OFF
ON
OFF
SeOpTi Waiting time till the drive mechanism closes even if SeOpCo = ON (safety element opening time), in the event
that a fixed object blocks the door (only visible if SeOpCo = ON)
PERMAN
1...60 s
20 s
SESClo Safety element Stop activated/deactivated during the closing motion (safety element stop closing) ACTIVE
INACTI
INACTI
EMY-IN Configuration of the Emergency terminal (break contact) (emergency input) CL-SPR (spring)
STOP
OPEN
CL-MOT (motor)
CL-SPR
OExStp Step-by-step control function (opening element step) OFF
OEI
OEO
KEY
RADIO
OFF
FPReset Acknowledment of the fire alarm by the fire alarm central
(only allowed in cases were the door is within sight distance of the fire alarm central)
OFF
ON
OFF
RC 0.1 Parametrizable relay output 1 on optional PCB 1 (relay contact)
(only visible if relay PCB 0 is plugged in)
CLOSED
OPENNG
OPEN
CLOSNG
ERROR
PSAUTO
PSNGHT
PSEXIT
PSOPEN
PSMANU
GONG
LOCKED
SIX30S
EMY_AL
CLOSED
RC 0.2 Parametrizable relay output 2 on optional PCB 1 (relay contact)
(only visible if relay PCB 0 is plugged in)
OPEN
RC 0.3 Parametrizable relay output 3 on optional PCB 1 (relay contact)
(only visible if relay PCB 0 is plugged in)
ERROR
RC 0.4 Parametrizable relay output 4 on optional PCB 1 (relay contact)
(only visible if relay PCB 0 is plugged in)
GONG
RC 1.1 Parametrizable relay output 1 on optional PCB 2 (relay contact)
(only visible if relay PCB 1 is plugged in)
OPENNG
RC 1.2 Parametrizable relay output 2 on optional PCB 2 (relay contact)
(only visible if relay PCB 1 is plugged in)
CLOSNG
RC 1.3 Parametrizable relay output 3 on optional PCB 2 (relay contact)
(only visible if relay PCB 1 is plugged in)
PSAUTO
RC 1.4 Parametrizable relay output 4 on optional PCB 2 (relay contact)
(only visible if relay PCB 1 is plugged in)
LOCKED
Unlock Impulse/Permanent unlocking (impulse unlock) IMPULS
PERMAN
IMPULS
UnloCl Retract the motor lock before closing (unlock) and lock, after the door leaf has been closed.
By engaging the lock latch, the closing noise of the door is reduced.
(unlock while closing)
Inactive
Active
Inactive
EL-Fb Return signal of the electric lock (electric lock feed back)
N.O.

Contact open if in the unlocked state (–), closed if in the locked state (+)
N.C.

Contact open in the locked state (+), closed in the unlocked state (–)
(+) and (–) indicate the status in the diagnostic menu
OFF
N.O.
N.C.
OFF
LockAU Operating mode AUTOMATIC locked (locked automat)
(only visible if Unlock = Perman)
UNLOCK
LOCK
UNLOCK
LockEX Operating mode EXIT locked (locked exit)
(only visible if Unlock = Perman)
UNLOCK
LOCK
LOCK
LockMA Operating mode MANUAL locked (locked manual)
(only visible if Unlock = Perman)
UNLOCK
LOCK
UNLOCK
LcdDir Orientation of the display (LCD direction) 0...1 0
MovCon Endurance test Open/Close (moving continuous) OFF
ON-FLT
ON-PRM
OFF
OExMAN Acceptance of opening commands after a manual door opening (only if APuGo = OFF)
(opening element inside/outside manual)
OFF
ON
OFF
OEOSIR Safety device on opposite side to door hinge as opening element (only from Closed position).
Note: This parameter must be set to OFF for teaching-in of the LZR-FLATSCAN.
(SER as OEO)
OFF
ON
OFF
FPMaOp Fire alarm acknowledgement by manually opening and holding the door leaf in the taught-in open position.
(fire protection manual opening)
OFF
ON
OFF
FPMaCl Fire alarm triggering by manual closing of the door leaf from the open position.
(fire protection manual closing)
OFF
ON
OFF