manualshive.com logo in svg

Glow-worm COMPACT 80p, Instructions For Use, Installation & Servicing

Share
Download
Glow-worm COMPACT 80p Instructions For Use, Installation & Servicing Download Page 26

Supplied By www.heating spares.co  Tel. 0161 620 6677

26

221679H

PILOT WILL NOT LIGHT
START HERE

Check gas line-open all cocks,
rectify any blockages, purge out 
any air. Does pilot light?

Apply match to pilot burner instead
of pressing piezo unit button.
Does pilot light?

Undo tubing nut at pilot burner.
Turn gas valve knob to Pilot/Ign.
Press multi-functional control knob.
Does gas flow freely?

Rectify blockage in pilot injector,
or renew pilot injector.

Undo tubing nut at pilot outlet
of the multi-functional control.
Press gas valve knob.
Does gas flow freely?

Rectify or replace
blocked pilot tube.

Change multi-functional control.

Does pilot stay alight when
multi-functional control 
knob is released?

PILOT SATISFACTORY

Does pilot flame envelop 
thermocouple?

Check aeration. If necessary -
Clean pilot, rectify blockage in
pilot injector, or replace.

Check thermocouple circuit using
Thermocouple fault finding diagram.

On pressing piezo unit button is
there a spark across electrode gap?

Pull ignition lead off electrode. Hold end of 
lead close to pilot burner and operate 
piezo unit. Is there a spark across gap?

Is there continuity of piezo earth?

Repair or replace earth lead.

Pull ignition lead off piezo unit.
Using blade of a screwdriver, touch unit 
chassis and leave approx. 4mm gap from 
connection tag onpiezo unit. Operate piezo.
Is there a spark across gap? 

Change
piezo unit.

Change
ignition lead.

Check electrode gap. Reposition,
or replace electrode as necessary.

NO

YES

NO

YES

NO

YES

NO

YES

NO

YES

NO

YES

NO

YES

NO

YES

YES

NO

NO

YES

13 Fault Finding

Diagram 13.3

7460

PILOT FAULT FINDING

Summary of Contents for COMPACT 80p













































Reviews:

No comments

Brands by name

Popular brands

Load more brands