Gigaset SX763 First Steps Download Page 165

Page: 165 / 196

165

Appendix

Gigaset SX763 WLAN dsl / eng / A31008-M707-R131-8x-7619 / appendix.fm / 23.10.2008

e 20

05_

_27

The

LAN

LED on a con-

nected device does not light
up.

No LAN connection

Make sure the connected device is turned on.

Check whether the Ethernet cable is plugged in.

Check that you are using the right cable type
(CAT5) and that the cable is not too long (<100m).

Check that the network card on the connected
device and the cables are not defective. If neces-
sary, replace a defective network card or cable.

Use the Windows device manager (

My Computer

–

Properties

) to check whether the network card is

functioning. If you see a red cross or a question
mark, the driver may not have been installed or
there is a resource conflict. Follow the Windows
instructions to remedy the problem.

You cannot connect to the
Internet.

Check whether the

Connect manually

option is

activated. If it is, connections cannot be opened
automatically.

Select

Connect on demand

Always on

Remember that this setting may lead to higher
costs if you are billed on the time used.

The connection may have been terminated manu-
ally with the

Connect on demand

option selected.

– Restore the connection again manually using the

Connect

button or

– Restart the Gigaset SX763 WLAN dsl.
In both cases, the

Connect on demand

setting will

be active again.

Check whether the data entered for your Internet
connection matches what your Internet service
provider has specified.

After a WPS registration
attempt, the

WLAN

LED

continues to flash for some
time and the required client
was not registered.

More than one client has tried to register.

Repeat registration after a short interval.

MAC access control is activated, but the desired cli-
ent is not in the MAC address list.

Add the client to the MAC address list (see
page 59).

If the MAC address filter is enabled a WPS registration
attempt can not be detected by the device. In this case
LED signalling is not possible.

Symptom

Possible cause and solutions

Summary of Contents for SX763





































































































































































































Search results

Summary of Contents for SX763

Reviews:

Related manuals for SX763

Brands by name

Popular brands

Gigaset SX763, First Steps

Search results

Summary of Contents for SX763

Reviews:

Related manuals for SX763

Brands by name

Popular brands