Gigaset SX763 First Steps Download Page 118

Page: 118 / 196

118

Configuring Advanced Settings

Gigaset SX763 WLAN dsl / eng / A31008-M707-R131-8x-7619 / configure_router.fm / 23.10.2008

e 20

05_

_27

Choose the

Directory

in which the data is stored on the USB mass storage device

using the

Browse

button.

You can allow general access for both FTP services, or only for selected users with a user
name and password.

For

Access (read only)

, select whether all users should be able to read your data in

Anonymous

mode or whether only one

Specified user

should be supported.

Specify whether

Access (full control)

to your data should be

disabled

or whether a

Specified user

may read, edit and delete your data.

Enter the name in the

Specified user

field. Define different user names for the dif-

ferent access type and directory.

Enter the password for the user and confirm it by entering it again in the field below.
The password is case-sensitive. Avoid using proper names and obvious terms.
Instead, use upper case and lower case letters, numbers and special characters.

Click

to apply the changes.

Summary of Contents for SX763





































































































































































































Search results

Summary of Contents for SX763

Reviews:

Related manuals for SX763

Brands by name

Popular brands

Gigaset SX763, First Steps

Search results

Summary of Contents for SX763

Reviews:

Related manuals for SX763

Brands by name

Popular brands