Genie AWP Super Series Service Manual Download Page 6

Page: 6 / 207

Service Manual

September 2016

Safety Rules

P Super Series • IWP Super Series

Part No. 38139

Section 1

Safety

R ules

Gener al Safety R ules

Danger

Failure to obey the instructions and safety rules in

this manual and the appropriate Operator's Manual

on your machine will result in death or serious

injury.

Many of the hazards identified in the operator's

manual are

also safety hazards when maintenance

and repair procedures are performed.

Do Not Perform Maintenance

Unless:



You are trained and qualified to perform

maintenance on this machine.



You read, understand and obey:

•

manufacturer's instructions and safety rules

•

employer's safety rules and worksite

regulations

•

applicable governmental regulations



You have the appropriate tools, lifting

equipment and a suitable workshop.

Summary of Contents for AWP Super Series
















































































































































































































Search results

Summary of Contents for AWP Super Series

Reviews:

Related manuals for AWP Super Series

Brands by name

Popular brands

Genie AWP Super Series, Service Manual

Search results

Summary of Contents for AWP Super Series

Reviews:

Related manuals for AWP Super Series

Brands by name

Popular brands