![background image](http://html1.mh-extra.com/html/gehl/rs5-19/rs5-19_operators-manual_2205883033.webp)
PRINTED IN U.S.A.
31
50960066/AP0813
The Exhaust Filter Cleaning Indicator will illuminate
when the system is actively performing an exhaust fil-
ter cleaning. When the exhaust filter cleaning process
has completed its cycle, the cleaning indicator will turn
off.
The machine can be operated as normal during the auto
exhaust filter cleaning process unless the operator
determines the machine is not in a safe location for
high exhaust temperatures and disables the auto clean-
ing process.
To enable the auto exhaust filter cleaning mode, the
exhaust filter cleaning rocker switch should be in the
center position.
IMPORTANT:
It is recommended that the exhaust
filter cleaning be in the Auto mode at all times.
Auto mode should only be disabled when the
machine is not in a safe location during the
exhaust filter cleaning process.
If the machine is not able to be moved to a safe loca-
tion, the operator should temporarily disable auto
exhaust filter cleaning. If the machine is located in a
safe location, the auto mode should always be enabled.
Manual/Parked Exhaust Filter Cleaning
Manual/Parked exhaust filter cleaning is initiated by
the operator. This process allows the system to clean
the exhaust filter when the operator previously needed
to disable the auto exhaust cleaning process because of
specific conditions. During this process the engine
speed will be controlled by the ECU. The machine
must remain parked during this process.
NOTE:
It is not necessary to perform a
manual/parked exhaust cleaning unless a previ-
ous auto cleaning process was cancelled and the
indicator in the exhaust filter gauge is illuminated.
Cleaning times will vary depending upon several spe-
cific criteria. The average standard cleaning time can
range from 20 - 50 minutes or longer.
To enable manual/parked exhaust filter cleaning;
1.
Park the machine in a safe location and check that
the machine has a recommended 1/4 tank of fuel
to complete the process.
2.
Reduce engine speed to low idle and apply the
parking brake.
3.
Press the top of the exhaust filter cleaning switch
for approximately 3 seconds until the indicator in
the switch illuminates. The cleaning indicator in
the exhaust filter gauge will also illuminate.
The indicators will go off when the exhaust filter
cleaning process is completed. If the machine is not
going to be returned to service immediately after the
cleaning process, allow the engine and the exhaust fil-
ter time to return to normal operating temperature
before stopping the engine. The manual/parked filter
cleaning process can be canceled at any time during the
process.
Avoid disabling the cleaning process unless absolutely
necessary. Repeated disabling or ignoring prompts to
perform a manual/parked cleaning procedure will
cause additional engine power limitations and can
eventually lead to dealer required service.
Utilize AUTO Exhaust Filter Cleaning mode to avoid
additional service.
Disable Exhaust Filter Cleaning
Disabling the exhaust filter cleaning request is not rec-
ommended. Disable the automatic exhaust filter clean-
ing only when necessary. Whenever possible, cleaning
should be allowed and the exhaust filter cleaning
switch should be left in the AUTO Mode. When left in
auto mode, soot buildup in the exhaust filter system
will be at a minimum.
To disable exhaust filter cleaning, press the bottom of
the exhaust filter cleaning rocker switch. The Auto
Cleaning Disabled Indicator located in the exhaust fil-
ter gauge will be illuminated.
WARNING
During auto or manual exhaust filter cleaning
operations, the engine will run at elevated idle
and hot temperatures for approximately 30
minutes. Exhaust gases and exhaust filter
components reach temperatures hot enough
to burn people, ignite, or melt common mate-
rials.
Servicing the machine or attachments during
exhaust filter cleaning can result in serious
personal injury. Avoid exposure and skin con-
tact with hot exhaust gases and components.
If the machine is not in a safe location for ele-
vated temperatures, move the machine to a
safe location and check for adequate fuel level
before beginning the exhaust filter cleaning
process.
Summary of Contents for RS5-19
