Gehl RS5-19, Operator'S Manual

Page: 21 / 82

PRINTED IN U.S.A.
19
50960066/AP0813
B - Scroll Button: Pressing this button changes the
function displayed in the multi-function display
screen.
Press and hold the button in for 3 seconds to tog-
gle the engine coolant tmperature reading between
celsius and fahrenheit.
A1 - Fuel Level Gauge:
The fuel level is displayed at
all times in the lower portion of the display. It indicates
the amount of fuel remaining in the fuel tank.
A2 - Engine Coolant Temperature:
Press button “B”
until “TEMP” is displayed. It indicates the temperature
of the engine coolant. Under normal conditions, this
should indicate approximately 185°F (85°C).
A3 - Engine Speed:
Press button “B” until “RPM” is
displayed. This indicates the engine speed.
A4 - Voltmeter: Press button “B” until “VOLTS” is
displayed. This indicates the voltage output from the
alternator.
A5 - Hourmeter: Press button “B” until “HRS” is dis-
played. It indicates the total operating time of the
machine and should be used for keeping the mainte-
nance log.
A6 - Maintenance Reminder: After every 250 hours
a reminder will display: “ROUTINE MAINTENACE
IS REQUIRED
⎯
CHECK OPERATOR’S MANU-
AL.” Perform the required maintenance, and then clear
the message by pressing and holding button “B” until
the message is cleared.
NOTE: The maintenance reminder message
must display at least three minutes before it can
be cleared by pressing and holding button “B”.
A7 - Error Fault Code: Error codes and a short error
description are displayed in this screen. The error code
will clear when the error is corrected.
A8 - DPF Regeneration: If the auto regen has been
disabled or an auto regen is in process, a message will
be displayed indicating the need for a DPF regenera-
tion along with the level of regeneration needed as
“LOW”, “MEDIUM” OR “HIGH”.
Indicator Lamps
C - Engine Failure:
This lamp when lit, alerts the
operator of a fault condition. Refer to the multi-func-
tion display screen for error codes.
D - Engine Oil Pressure Lamp: This lamp indicates
when the engine lubricating oil pressure is too low.
During normal operation, with the engine running, this
lamp should be off. During starting and when the igni-
tion is on but the engine is not running, this lamp will
be on.
IMPORTANT: If this lamp comes on during nor-
mal operation, stop the engine immediately! After
allowing the oil to drain down for a few minutes,
check the engine oil level. Maintain oil level at the
FULL mark on the dipstick.
E - Engine Coolant Temperature Lamp: This lamp
indicates when the temperature of the engine coolant is
too high.
IMPORTANT: If this lamp comes on during nor-
mal operation with the engine running, STOP the
engine as soon as possible and check the engine
cooling system.
F - Alternator Lamp: This lamp indicates the condi-
tion of the electrical charging system. During normal
operation, this lamp should be off. If the charge rate is
too high or too low, this lamp will come on.
G - Air Cleaner Restriction Indicator Lamp: If this
lamp comes on, the engine air filter requires service.
H - Engine Pre-heat Indicator Lamp:
When lighted
this lamp indicates that the cold weather starting aid is
in use.
I - Hydrostatic Transmission Oil Temperature
Lamp:
This lamp indicates when the temperature of
the transmission oil is too high. During normal opera-
tion this lamp should be off, indicating that the trans-
mission oil system is at the proper temperature.
IMPORTANT: If this lamp comes on during nor-
mal operation, a problem may exist in the trans-
mission oil system. Stop the machine immediate-
ly and investigate the cause of the problem!
J - Low Fuel Lamp:
This lamp indicates a low fuel
situation. The fuel tank should be filled as soon as pos-
sible.
K - Hydraulic Oil Filter Restriction Lamp:
If this
lamp comes on, the hydraulic oil filter requires service.