manualshive.com logo in svg

Geberit Chicago Faucets Commander, Manual

Share
Download
Geberit Chicago Faucets Commander Manual Download Page 16

Chicago Faucets

®

 Commander

™

 Handheld Programming Unit User Guide 

Page 16 

CF2026  /  07/19

SECTION 2: Scanning, Mode and Setting Adjustments

2.6.1   Running Mode 

 

Running Mode

 — enable, disable or adjust specific water on/off modes of fitting  

 

   

 

   to meet user needs and/or remove user inconvenience.

Normal Mode

 — Fitting operates when user 

is detected and stops immediately after user 
detection ends. Default factory mode (for non-
SSPS fittings). 

See Section 2.6.1.1 for more 

details.

Metering Mode

 — Fitting operates only when 

user is detected and stops after a prescribed 
amount of time.

 See Section 2.6.1.2 for more 

details.

Cleaning Mode

 — Fitting is deactivated and 

will not operate when user is detected to allow 
cleaning or maintenance without running water.

 

See Section 2.6.1.3 for more details.

Scrub Mode

 — Fitting can be set for longer run 

times for scrub sinks. Automatically runs after user is 
detected and does not end until after assigned time.

  

See Section 2.6.1.4 for more details.

Water Saver Mode

 — Fitting operates when user 

is detected and stops after a brief delay when user 
detection ends. Default factory mode (for SSPS 
fittings).

 See Section 2.6.1.5 for more details.

Summary of Contents for Chicago Faucets Commander













































Reviews:

No comments

Brands by name

Popular brands

Load more brands