background image

18

Additional Specifications For  
GE Vertical Zoneline

®

 Heat Pumps

Heat pump unit shall automatically switch from heat pump 
operation to electric resistance heat when it is unable to 
provide sufficient heat to maintain room temperature or  
when the outdoor temperature falls below 25°F.
Unit shall be equipped with a temperature activated valve  
to allow condensate water generated during defrost cycles  
to drain into the specified drain system.
Unit shall have a concealed switch to allow heat pump 
operation to be overridden and heat provided by electric 
resistance heaters regardless of outdoor temperatures. 
Heat pump unit shall have Reverse Cycle (hot gas) Defrost 
system to maximize heat pump operation and minimize 
energy consumption. 
To minimize energy consumption, units shall have electric 
heaters locked out when outdoor temperatures are above 
46°F. Heating will be provided by heat pump operation only.   
In the event of a compressor failure during heat pump 
operation, the unit shall automatically switch to electric 
resistance heat to maintain selected room temperature 
regardless of outdoor temperatures. 
When the heat mode is selected or when the unit is switched 
from off to on in heat mode, the unit shall energize electric 
heaters to quickly warm the room to wall thermostat set  
point. Heat pump operation will resume on subsequent 
heating requirements.
Unit shall have an indoor coil temperature sensor to protect 
the compressor when the outdoor temperatures are too high 
for heat pump operation.    

Additional Specifications Service

Submit complete information with bid covering service 
availability, to whom service on units will be assigned, 
complete address and phone number, including phone  
number of emergency service personnel.

Startup, Adjust, Demonstrate

Contractor shall be responsible for the initial starting of  
units, adjustments thereto, cleaning, etc.; to place the units  
in required operating condition. Contractor shall demonstrate 
to the owner, or his representative, the operation of units for 
both summer and winter functions.

Limited Warranty

For one year from date of original purchase, manufacturer 
will provide, free of charge, parts and service labor on site to 
repair or replace any part of the Zoneline that fails because of 
a manufacturing defect. 
For an additional four years from the date of original purchase, 
manufacturer will provide, free of charge, parts and on-site 
service labor to repair or replace any part of the sealed 
refrigerating system (compressor, condenser, evaporator, and 
all connecting tubing) that fails due to a manufacturing defect. 
For the second through fifth year from the date of original 
purchase, the manufacturer will provide a limited parts 
warranty. The manufacturer will provide, free of charge, 
parts that fail as a result of a manufacturing defect. Parts 
covered are fan motors, switches, heater, heater protectors, 
compressor overload, solenoids, circuit boards, auxiliary 
controls, thermistors, frost controls, capacitors, and varistors. 
This limited parts warranty does not include labor or 
transportation to and from the service shop.
All warranty service is to be provided by manufacturers 
factory service centers or by their authorized servicers during 
normal working hours.

Summary of Contents for Zoneline





















Reviews: