GE VP11 Reference Manual Download Page 65

Page: 65 / 118

Interrupts

The interrupt routing for standard components such as COM1/2 is in
compliance with standard PC/AT systems. Unused interrupts can be used for
add-on cards or other board specific PCI devices such as SCSI and Ethernet.

Table 20: Interrupt assignments

Hardware IRQ

IRQ Source

INTC1

IRQ00

System Timer

IRQ01

Keyboard

IRQ02

Cascade from INTC2

IRQ03

COM2 / COM1

IRQ04

COM1 / COM2

IRQ05

IRQ06

IRQ07

INTC2

IRQ08

Real Time Clock

IRQ09

Power Management Contr.

IRQ10

PnP/PCI

IRQ11

PnP/PCI

IRQ12

PS/2 Mouse

IRQ13

Numeric Coprocessor

IRQ14

External IDE

IRQ15

Onboard IDE

NMI Parity

Error,

ECC Error,

System Error

. Emulated interrupt from USB keyboard/mouse.

. Interrupts are available for Plug and Play PCI devices

. This interrupt is available for other devices when the primary IDE is disabled

in SETUP or when IDE is configured to 'native PCI' mode.

. This interrupt is available when the secondary IDE is disabled in SETUP or

when IDE is configured to 'native PCI' mode.

GE Intelligent Platforms – VR11, VP11 Hardware Reference Manual, Second Edition

Page 65

Summary of Contents for VP11























































































































Search results

Summary of Contents for VP11

Reviews:

Related manuals for VP11

Brands by name

Popular brands

GE VP11, Reference Manual

Search results

Summary of Contents for VP11

Reviews:

Related manuals for VP11

Brands by name

Popular brands