GE VP11 Reference Manual Download Page 33 | Manualshive

Page: 33 / 118

background image

CHAPTER 3

Installation

Chapter Scope

This chapter covers the installation of the VR11 VME Single Board Computer
on a VME backplane and initial power-on operations.

Installation preparation

Use the following steps to install your GE Intelligent Platforms hardware.

•

Before installing or removing any board, please ensure that the system
power and external supplies have been turned off.

•

Check that the jumpers and mezzanines are correctly configured for your
application.

•

Mount the board/mezzanine/transition module very carefully. See also
additional advisories for VMEbus and CompactPCI products below.

•

Connect all IO cables.

•

Once you are certain that all modules are correctly fitted into the system
and all connections have been made properly, restore the power.

General advice

Please observe all safety procedures to avoid damaging system and protect
operators and users.

Before installing or removing any board, please ensure that the system power
and external supplies have been turned off.

Check that jumpers and mezzanines are correctly configured for your
application. Mount the board, mezzanine, or transition module very carefully.
See also sections on additional advisories below.

Do not restore power until you are sure that all modules are fitted correctly and
all connections have been made properly.

GE Intelligent Platforms – VR11, VP11 Hardware Reference Manual, Second Edition

Page 33

«
...
31
32
33
34
35
...
»

Summary of Contents for VP11























































































































Reviews:

No comments

Related manuals for VP11

Brand: P&E Microcomputer Systems Pages: 59

Brand: Yamaha Pages: 86

Brand: Microchip Technology Pages: 17

Brand: Texas Instruments Pages: 16

otometrics HI-PRO 2

Brand: natus Pages: 22

Brand: TYAN Pages: 64

MT9J003I12STCVH-GEVB

Brand: ON Semiconductor Pages: 5

Brand: TYAN Pages: 63

Brand: JETWAY Pages: 70

Brand: ASROCK Pages: 257

Brand: Supermicro Pages: 111

Brand: Texas Instruments Pages: 51

Brand: Intel Pages: 62

AIMB-742 Socket 478

Brand: Intel Pages: 4

ConnectCore 6UL SBC Pro

Brand: Digi Pages: 54

Brand: ASROCK Pages: 35

Brand: BCM Advanced Research Pages: 9

Brand: ON Semiconductor Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands