GE VP11 Reference Manual Download Page 80 | Manualshive

Page: 80 / 118

background image

Figure 19: Battery removal

Note:
If the battery is exchanged by the customer, please use the same type of
battery and ensure correct polarization

.

For operating without battery please check the following description of the
external battery input

.

Battery removal and replacement

Locate battery on the computer. Reference the product manual if it is not easily
located. On some of the dual slot SBCs, the top board may need to be removed
to make it easier to remove the battery. Once the battery is located, take a non-
conductive tool and push at the back of the battery holder. Gently apply
pressure in order to not break the socket. The battery should slide forward out
of the holder. Pressure can be alternated between the two sides to get the
battery to slide out of the socket. The battery should slide forward enough that
it could be removed from the socket. A new battery can be installed by sliding
it into the holder. Make sure to observe correct polarity.

+5VSTDBY

The RTC can be supplied by this voltage if there is no battery onboard. It is
located at VME-Connector P1 (P7301) pin B31.

Without an onboard battery it is recommended to use an external supply
connected to this input. This voltage supplies the real time clock and the CMOS
RAM for storing the BIOS Setup settings.

GE Intelligent Platforms – VR11, VP11 Hardware Reference Manual, Second Edition

Page 80

«
...
78
79
80
81
82
...
»

Summary of Contents for VP11























































































































Reviews:

No comments

Related manuals for VP11

Brand: Alcad Pages: 98

Brand: SOYO Pages: 95

Brand: RAK Pages: 17

EmbCore ROM-7421

Brand: Advantech Pages: 25

Brand: NXP Semiconductors Pages: 14

Brand: Icop Pages: 40

Brand: ST Pages: 82

Brand: Ublox Pages: 21

Brand: Texas Instruments Pages: 21

Brand: Texas Instruments Pages: 19

Avnet Ultra96-PYNQ

Brand: Xilinx Pages: 19

Brand: EVGA Pages: 2

X570 PHANTOM GAMING 4

Brand: ASROCK Pages: 196

Z370 AORUS Gaming 7

Brand: Gigabyte Pages: 48

Brand: Supermicro Pages: 127

Brand: Nuvoton Pages: 11

S2257 THUNDER 2400

Brand: TYAN Pages: 105

Brand: Texas Instruments Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands