GE PAC8000 series User Manual Download

Page: 48 / 50

Contents

PAC8000* IO PROFINET Scanner

User’s Manual–September 2017

GFK-2839B

5.3

Limitations

The following features are

not supported

RT over UDP

IRT

Multicast communication

DHCP

DCP Hello service

DNS (Domain Name Service protocol)

FastStartUp

Supervisor-AR. Note: Supervisor-DA-AR is supported. (Device Access supported)

Optical power diagnostics (IC200PNS002)

CBA

Substitute Data

Only one Input-CR and one Output-CR are supported.

8515-BI-PN, 8
8516-BI-PN, 8
8752-CA-NS, 8
Automatic Restart

PAC8000 PROFINET Scanner, 41

Bussed field power supply(BFP)

monitoring, 12

Cables

clearance for, 21

Carriers

IO, 17
PNS, 17

Configuration

clearing, 37
getting started, 37
overview, 31

Controls and Indicators, 10
DIN rail, 23
Discovery and Configuration Protocol

(DCP), 37

Error Handling

PAC8000 PROFINET Scanner, 41

Ethernet Network Ports, 13
Fatal Error Blink Pattern, 28
Fatal error handling, 41
Faults

clearing, 44
module loss, add and mismatch, 45

Firmware Update Mode Blink Patterns, 28
Firmware updates

PAC8000 modules in remote node, 29
PAC8000 PROFINET Scanner, 29

Grounding, 25
Hazardous Locations, 22
Installation, 19

cables, 21
PAC8000 PROFINET Scanner, 19
replacing PROFINET Scanner

hardware, 37

IP addresses, 9
LEDs, 10

blink patterns, 28
operation, 27

MAC Addresses, 9
Media Redundancy Protocol (MRP), 16
Module Identification LED Pattern, 28
Modules, carriers, and power supplies, 17
Operating Temperature Range, 9
Output Control Bits

PAC8000 PROFINET Scanner, 38

PAC8000 Module Parameters

configuration, 36

PAC8000 PROFINET Scanner

Summary of Contents for PAC8000 series



















































Search results

Summary of Contents for PAC8000 series

Reviews:

Related manuals for PAC8000 series

Brands by name

Popular brands

GE PAC8000 series, User Manual

Search results

Summary of Contents for PAC8000 series

Reviews:

Related manuals for PAC8000 series

Brands by name

Popular brands