GE PAC8000 series User Manual Download

Page: 47 / 50

Index

GFK-2839B

PAC8000* IO PROFINET Scanner

User’s Manual–September 2017

Chapter 5.

PROFINET Specifications

Release 2.00 of the PAC8000 PROFINET Scanner supports PROFINET v2.3 Class A

IO-Device with the clarifications listed below. For version-specific updates, refer to the
Important Product Information document provided with your module.

5.1

PROFINET Protocol Support

RTC

– Real time Cyclic Protocol: RT_CLASS_1 & RT_CLASS_2

RTA

– Real time Acyclic Protocol

DCP

– Discovery and Configuration Protocol

CL-RPC

– Connectionless Remote Procedure Call

LLDP

– Link Layer Discovery Protocol – transmission only

MRP

– Client role only (Manager role not supported)

PTCP

– Precision Transparent Clock Protocol – Line delay measurement only

5.2

Technical Data

API:

Single API (0) used.

Number of Application Relations
supported:

1 (Additional Supervisor-DA-AR allowed)

Number of System Redundancy
Application Relations (SR-AR) sets
supported

Maximum length of cyclic input
data:

1440 bytes

Maximum length of output data:

1440 bytes

Alarm Types:

Pull, Plug, PlugWrong

DCP:

Get/Set/Identify supported. Only All and Name Of
Station filters supported

Identification & Maintenance:

I&M0 only

Context Management:

by CL-RPC

Minimum cycle time:

1ms

Ethernet rate:

100 Mbit/s full duplex with auto-negotiation

Summary of Contents for PAC8000 series



















































Search results

Summary of Contents for PAC8000 series

Reviews:

Related manuals for PAC8000 series

Brands by name

Popular brands

GE PAC8000 series, User Manual

Search results

Summary of Contents for PAC8000 series

Reviews:

Related manuals for PAC8000 series

Brands by name

Popular brands