GE Druck ADTS 2 Series User Manual Download Page 68 | Manualshive

Page: 68 / 70

background image

Druck ADTS 2XX User Manual

56

K0451 Issue No. 1

6.2 Air Data Specifications

Note:

All range values at maximum limits.

Ps 1 Port

Pressure Mode

Control Range: ................................................................................................................... 35

(1)

to 1355 mbar a

Measure Range: .................................................................................................................. 27.6 to 1355 mbar a
Resolution: ....................................................................................................................................................0.01mbar
Accuracy: .....................................................................................................................................................±0.1 mbar
Rate Range:............................................................................................................................0 to 1000 mbar/min
Rate Accuracy: .................................................................................................................. ±1% of aim (average)

Aeronautical Mode

Control Range: ........................................................................................................................ -2000 to 60,000 ft.
Measure Range: ..................................................................................................................... -3000 to 100,000ft.
Resolution: ................................................................................................................................................................ 1 ft.
Accuracy: ......................................................................................................................................±3 ft. (@sea level)

..............................................................................................................................................±7 ft. (@30,000 ft)
...........................................................................................................................................±23 ft. (@55,000 ft)

Rate Range:.................................................................................................................................0 to 40,000 ft/min
Rate Accuracy: .................................................................................................................. ±1% of aim (average)

Ps 2 Port

Pressure Mode

Control Range: ................................................................................................................... 35

(1)

to 1355 mbar a

Measure Range: .................................................................................................................. 27.6 to 1355 mbar a
Resolution: ....................................................................................................................................................0.01mbar
Accuracy: .....................................................................................................................................................±0.1 mbar
Rate Range:............................................................................................................................0 to 1000 mbar/min
Rate Accuracy: .................................................................................................................. ±1% of aim (average)

Aeronautical Mode

Control Range: ........................................................................................................................ -2000 to 60,000 ft.
Measure Range: ..................................................................................................................... -3000 to 100,000ft.
Resolution: ................................................................................................................................................................ 1 ft.
Accuracy: ......................................................................................................................................±3 ft. (@sea level)

..............................................................................................................................................±7 ft. (@30,000 ft)
...........................................................................................................................................±23 ft. (@55,000 ft)

Rate Range:.................................................................................................................................0 to 40,000 ft/min
Rate Accuracy: .................................................................................................................. ±1% of aim (average)

(1)

limited only by vacuum pump/system leaks

«
...
66
67
68
69
70
»

Summary of Contents for Druck ADTS 2 Series







































































Reviews:

No comments

Related manuals for Druck ADTS 2 Series

Brand: GALBIATI Pages: 20

Brand: dbx Pages: 12

Brand: dbx Pages: 13

Brand: dbx Pages: 72

Brand: dbx Pages: 11

Brand: dbx Pages: 16

Brand: Kamikaze Pages: 112

Brand: KAM Pages: 2

Brand: Kärcher Pages: 88

Brand: H&S Pages: 42

Brand: Nellcor Pages: 161

OXIMAX N-600X Series

Brand: Nellcor Pages: 210

Brand: Oase Pages: 120

Brand: OAKWORKS Pages: 24

Brand: Valko Pages: 10

Brand: Opvimus Pages: 50

Brand: Bayer HealthCare Pages: 104

EDC2-1001-RGB-MWT

Brand: Energizer Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands