GE D30D00HCHF8AH6AM6BP8BX7A, Instruction Manual

Page: 163 / 646

GE Multilin D30 Line Distance Protection System 5-37
5 SETTINGS 5.2 PRODUCT SETUP
5
– Set
REMOTE DEVICE 1 ETYPE APPID
to match the ETHERTYPE application ID from the transmitting device. This is
“0” in the example above.
– Set the
REMOTE DEVICE 1 DATASET
value. This value represents the dataset number in use. Since we are using
configurable GOOSE 1 in this example, program this value as “GOOSEIn 1”.
3. Configure the Boolean data by making the following changes in the
INPUTS/OUTPUTS

REMOTE INPUTS

REMOTE
INPUT 1
settings menu:
– Set
REMOTE IN 1 DEVICE
to “GOOSEOut_1”.
– Set
REMOTE IN 1 ITEM
to “Dataset Item 2”. This assigns the value of the GGIO3.ST.Ind1.stVal single point status
item to remote input 1.
4. Configure the analog data by making the following changes in the
INPUTS/OUTPUTS

IEC 61850 GOOSE ANALOG
INPUTS
settings menu:
– Set the
IEC61850 GOOSE ANALOG INPUT 1 DEFAULT VALUE
to “60.000”.
– Enter “Hz” for the
IEC61850 GOOSE ANALOG INPUT 1 UNITS
setting.
The GOOSE analog input 1 can now be used as a FlexAnalog value in a FlexElement or in other settings. The D30 must be
rebooted (control power removed and re-applied) before these settings take effect.
The value of GOOSE analog input 1 in the receiving device will be determined by the MMXU1.MX.Hz.mag.f value in the
sending device. This MMXU value is determined by the source 1 frequency value and the MMXU Hz deadband setting of
the sending device.
Remote input 1 can now be used in FlexLogic equations or other settings. The D30 must be rebooted (control power
removed and re-applied) before these settings take effect.
The value of remote input 1 (Boolean on or off) in the receiving device will be determined by the GGIO1.ST.Ind1.stVal value
in the sending device. The above settings will be automatically populated by the EnerVista UR Setup software when a com-
plete SCD file is created by third party substation configurator software.
For intercommunication between D30 IEDs, the fixed (DNA/UserSt) dataset can be used. The DNA/UserSt dataset con-
tains the same DNA and UserSt bit pairs that are included in GSSE messages. All GOOSE messages transmitted by the
D30 (DNA/UserSt dataset and configurable datasets) use the IEC 61850 GOOSE messaging services (for example, VLAN
support).
Set the
CONFIG GSE 1 FUNCTION
function to “Disabled” when configuration changes are required. Once changes are
entered, return the
CONFIG GSE 1 FUNCTION
to “Enabled” and restart the unit for changes to take effect.
PATH: SETTINGS

PRODUCT SETUP

COMMUNICATIONS

IEC 61850 PROTOCOL

GSSE/GOOSE CONFIGURATION

TRANSMISSION

CONFIGURABLE GOOSE

CONFIGURABLE GOOSE 1(8)

CONFIG GSE 1(64) DATA ITEMS
To create a configurable GOOSE dataset that contains an IEC 61850 Single Point Status indication and its associated qual-
ity flags, the following dataset items can be selected: “GGIO1.ST.Ind1.stVal” and “GGIO1.ST.Ind1.q”. The D30 will then cre-
ate a dataset containing these two data items. The status value for GGIO1.ST.Ind1.stVal is determined by the FlexLogic
operand assigned to GGIO1 indication 1. Changes to this operand will result in the transmission of GOOSE messages con-
taining the defined dataset.

CONFIG GSE 1

DATASET ITEMS
ITEM 1:
GGIO1.ST.Ind1.stVal
Range: all valid MMS data item references for
transmitted data
MESSAGE
ITEM 2:
GGIO1.ST.IndPos1.stV
Range: all valid MMS data item references for
transmitted data
MESSAGE
ITEM 3:
None
Range: all valid MMS data item references for
transmitted data
↓
MESSAGE
ITEM 64:
None
Range: all valid MMS data item references for
transmitted data
NOTE