manualshive.com logo in svg

GE CyberDome Series, Installation Manual, Page: 8 / 52

Share
Download
GE CyberDome Series Installation Manual Download Page 8

Housing Installation

CyberDome Series Installation Manual

8

A06-8SG0/B/April2006/1033921C

Method 1: Installation Into T-Bar Ceilings

A T-bar type ceiling consists of a metal grid, which is used to suspend removable panels.
See 

Figure 5

. The panels will be either 24 in. x 24 in. (60.96 cm x 60.96 cm) or 24 in. x 48 in.

(60.96 cm x 121.92 cm). Installation into this type of ceiling requires a KTA-22-6 T-bar Mount-
ing Panel (24 in. x 24 in., i.e., 60.96 cm x 60.96 cm) or a KTA-24-6 T-Bar Support Kit (refer to

Appendix A

). 

The KTA-22-6 was formerly the KTA-00-6, and the KTA-24-6 the KTA-10-6.

6-inch Flush-mount Housing Installation

The indoor flush-mount housing can be installed into most types of ceilings, provided there is
sufficient clearance for the unit. See 

Figure 4

. The method of installation depends on the type

of ceiling into which the CyberDome is being mounted. Methods are:
•

Method 1 – Into T-bar ceilings 

(page 8)

•

Method 2 – Into non-removable false ceilings 

(page 11)

•

Method 3 – With superstructure attachment 

(page 15)

Figure 4:  False Ceiling Clearance

Figure 5:  T-Bar Ceiling with Mounting Panel

Summary of Contents for CyberDome Series





















































Reviews:

No comments